Digilent chipKIT Basic I/O Shield 참조 매뉴얼 - 페이지 6

{카테고리_이름} Digilent chipKIT Basic I/O Shield에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digilent chipKIT Basic I/O Shield 14 페이지.

페이지 인쇄

chipKIT™ Basic I/O Shield™ Reference Manual

The FETs are labeled Q1A (pin 9), Q1B (pin 6), Q2A (pin 5), and Q2B (pin 3). These four pins are also four of the

pulse width modulation (PWM) outputs supported by the chipKIT boards. The FETs can be switched using PWM via

the analogWrite function.

An FET is switched on by driving its gate high. When the FET is on, it provides a low impedance path to ground

(similar to a closed switch to ground). When the FET is switched off by driving its gate low, it becomes a high

impedance path to ground (similar to an open switch to ground). Pull-down resistors are connected to the gate of

each FET to ensure that it is off unless being actively driven high by the microcontroller on the chipKIT board.

The FET outputs are accessed via screw terminal connectors J7 and J8 on the left side of the shield. The digital

signals used to switch the FETs on and off are also available on screw terminal connectors J9 and J10 at the left

side of the upper edge of the shield.

Screw terminal connector J6 is used to make the power and ground connections back to the external power

supply. The negative (-) pin of J6 connects the external supply ground with the Basic I/O Shield ground, and the

positive (+) terminal connects the Basic I/O Shield to the external supply voltage.

The unloaded 2-pin header JP1 can be used to connect the shield's VCC5V0 power supply bus to the external

power supply bus so that the shield's 5V supply can be used instead of an external supply. In this case, J6 is used to

connect the shield's supply to the external loads. If this is done, the total current consumed by all external loads

must not exceed 2A or the current rating of the shield's power supply (whichever is less).

2.4

C Bus

The I

C bus from the chipKIT microcontroller board is brought onto the Basic I/O Shield. There are two I

on the board and a connector for taking the I

C Connector: Connector J11 can be used to extend the I

C devices. J11 is a standard 2x4 pin header connector with 0.100" spaced pins. It provides access to the I

signals, SCL and SDA, plus VCC3V3 and ground. The VCC3V3 can be used to power external I

The I

C bus uses open collector drivers to allow multiple devices to drive the bus signals. This means that pull-up

resistors must be provided to supply the logic high state for the signals. The Basic I/O Shield provides 2.2K-ohm

pull-up resistors. Generally, only one set of pull-up resistors is used on the bus. Jumpers JP2 and JP3 can be used to

disable the on-board pull-up resistors if a different value is needed or some other device on the bus is providing

the pull-ups. The on-board pull-up resistors are enabled by install shorting blocks on JP2 and JP3. Removing the

shorting blocks disables the pull-up resistors.

Digilent has several small I/O peripheral modules (Pmods) that can be connected using the I

include a 3-axis accelerometer, a 4-channel 12-bit A/D converter, a serial character LCD panel, a 3-axis gyroscope, a

real-time clock/calendar, and an I/O expander.

EEPROM: A 256Kbit (32Kbyte), I

the bottom left of the shield, just below the chipKIT logo.

The 7-bit I

C device address for the EEPROM is '1010000'.

Digilent has a library for using the EEPROM. It is contained in document # DSD-0000311 (chipKIT IOShield

Library.zip) which can be downloaded from the Basic I/O Shield product page at www.digilentinc.com. The

EEPROM library is IOShieldEEPROM.

Other product and company names mentioned may be trademarks of their respective owners.

C bus off the shield to connect to additional external I

C bus off of the shield to connect to additional external

C EEPROM is provided using a Microchip 24LC256. This EEPROM, IC1, is located on

C devices

C devices.

C connector. These

Page 6 of 13