Digilock Next Mech Dial Combo 제품 설명서
{카테고리_이름} Digilock Next Mech Dial Combo에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Digilock Next Mech Dial Combo 3 페이지.
페이지 인쇄
Lock Parts
Front Unit
Locked Position
Key Slot
Accommodates door
thickness up to 20 mm
Spacer required* for door
Installation Guide
thickness less than 8 mm
Mounting plate
Accommodates door
thickness up to 20 mm
Spacer required* for door
Accommodates door
thickness less than 8 mm
thickness up to 20 mm
Spacer required* for door
Mounting plate
Mounting
thickness less than 8 mm
Screws
Mounting plate
Mounting
Screws
Mounting
Screws
Manager key
Removal key
Operate with a Combination
Factory default combination 0-0-0-0
To Lock:
Manager key
Removal key
1.
Manager key
Close the door.
Removal key
2.
Make sure the knob is in the
Factory default combination 0-0-0-0
Factory default combination 0-0-0-0
unlocked
position.
3.
Set any 4-digit combination.
4.
Turn the knob to the locked
position.
5.
Scramble the combination.
Product Guide
Rear Unit
Unlocked Position
Core Removal
Position
Comibination Dial
Reset Pin Holes
Spacer Requirements
Door thickness
To Unlock:
1.
Enter your 4-digit
combination.
2.
Turn the knob to the
unlocked
position.
3.
Open the door.
4.
Scramble the combination.
Dial Combo
Cam in Locked Position
must overlap Strike
Mortise Hole Dimensions
Plate by at least ¼"
(6.35 mm)
Mortise Hole Dimensions
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Spacer Requirements
Door thickness
Screw type
0 – 5 mm
M3×10
5 – 8 mm
M3×14
8 – 12 mm
M3×10
12 – 16 mm
M3×14
16 – 20 mm
M3×18
Spacer Requirements
Door thickness
Screw type
*Spacer required
Operate with a Manager Key
Screw type
*Spacer required
0 – 5 mm
M3×10
✓
0 – 5 mm
M3×10
5 – 8 mm
M3×14
✓
5 – 8 mm
M3×14
8 – 12 mm
M3×10
8 – 12 mm
M3×10
12 – 16 mm
M3×14
To Unlock with Manager Key:
12 – 16 mm
M3×14
16 – 20 mm
M3×18
16 – 20 mm
M3×18
1.
Insert the Manager Key.
2.
Turn the knob to the
unlocked
symbol.
3.
Open the door.
Note: The Manager key provides instant access but does not erase
the code. The original code will continue to operate the lock even when
unlocking with the Manager Key.
If opened in error, use the Manager Key to turn the lock to the locked
position.
If the code is forgotten, follow the Reset Combination steps to make the lock
available for another user.
Shared Use
Cam
Mortise Hole Dimensions
min. 6.35 mm
31.5 mm
Accommodates door
thickness up to 20 mm
min. 6.35 mm
Spacer required* for door
31.5 mm
min. 6.35 mm
thickness less than 8 mm
31.5 mm
Mounting plate
Mounting
Screws
*Spacer required
✓
✓
✓
✓
Note "M" for
Manager on key
Manager key
Removal key
Factory default combination 0-0-0-0