Crest Audio 6001 사양 - 페이지 2
{카테고리_이름} Crest Audio 6001에 대한 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. Crest Audio 6001 2 페이지. Pro series
페이지 인쇄
8Ω Stereo Power
4Ω Stereo Power
2ΩStereo Power
8Ω Bridged Mono Power
4Ω Bridged Mono Power
Max RMS Output Voltage
(each channel)
Peak Output Voltage
(each channel)
Frequency Response
(+0 / -0.3dB, 1W/8Ω)
Power Bandwidth
(rated power at 4Ω, 1% THD+N)
Protection Circuitry
THD+N
(rated power at 4Ω, 1kHz)
SMPTE IMD
(rated power at 8Ω, 60Hz & 7kHz)
Damping Factor
(10-400Hz at 8Ω)
Input CMRR
Input Sensitivity
(rated power at 4Ω )
Voltage Gain
Input Impedance
Hum and Noise
("A" weighted, full power, 4Ω)
Crosstalk
("A" weighted, full power, 4Ω)
Input Connectors
Output Connectors
Filter Storage
Power Supply
(factory configured)
Idle Current Draw
1/8 Power Curr. Draw
(typical music, 120V/4Ω)
1/3 Power Curr. Draw
(continuous music, 120V/4Ω)
Max Curr. Draw
(circuit breaker rating, 120V/4Ω)
Thermal Emissions
(1/8 Power, 4Ω)
Thermal Emissions
(1/3 Power, 4Ω)
LED Indicators
Construction
Dimensions
(Height x Width x Depth)
Gross Weight, Net Weight
† USA, Canada, U.K., and many other countries. Power figures are watts per channel, both channels driven. Crest Audio reserves the
right to make improvements in manufacturing or design which may affect specifications. Crest Audio specification literature is available
in downloadable PDF file format; visit our website at http://www.crestaudio.com. ©1997 Crest Audio Inc. 5/21/97
Rear View
v. 2.3 4/9/97 B5100003
6 0 0 1 P O W E R A M P L I F I E R
S P E C I F I C AT I O N S
1kHz, <0.025% THD+N
430W
700W
800W
1320W
1500W
70V
99V
20 Hz-20 kHz, -3dB @ 53kHz
20 Hz-20 kHz, +0/-0.2dB
Clip Limit, IGM, AutoRamp, High Temp, short-circuit,
DC voltage, turn-on/off transient, sub/ultrasonic input.
<0.025%
<0.1%
400:1
>60 dB
(1kHz)
1.2V RMS
X40
>20kΩ
(balanced)
> -100 dB
> -60dB
Class
H
Female XLR (pin 3+), Octal Socket
(per channel)
5-way output binding posts
(per channel)
120,000 µF
100V-240V, 50-60Hz
1.1A
(120V)
5.96A
13.26A
21A
1844 BTU/hr
3838 BTU/hr
Cooling
Rear to front tunnel heatsink, variable speed DC fan
Controls
Front panel: 2 attenuators, circuit breaker/power switch;
Rear panel: mode switch, signal ground lift jumper.
Clip/Limit, Signal, Temp/DC, Active
(per channel)
16 ga. single piece steel chassis, .187" (5mm) alum. front panel
3.5"x19"x15" (16" to rear ears)
89mm x 483mm x 381mm (406mm to rear ears)
56.0 lbs. (25.42 kg.), 51.0 lbs. (23.10 kg.)
Warranty
5 years, parts and labor†
STEREO
A
IN
B
IN
PIN
3+
*B5100003*
20Hz-20kHz, <0.05% THD+N
400W
600W
720W
1200W
1440W
CAUTION
PARALLEL
A
BRIDGE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á
B
MAXIMUM
MODEL #
INPUT CURRENT
@ 120V, 60Hz
4801
18 AMPS
6001
21 AMPS
OUTPUT - CLASS 2 WIRING MAY BE USED
Architect's & Engineer's Specifications
The power amplifier shall have two channels. Each chan-
nel shall deliver a minimum of 400 watts at 8 ohms, 600
watts at 4 ohms, and 720 watts at 2 ohms; 20Hz - 20kHz,
<0.05% THD+N. In bridged mono mode, it shall deliver
1200 watts at 8 ohms and 1440 watts at 4 ohms, 20Hz -
20kHz, <0.05% THD+N.
The amplifier shall be rear-to-front tunnel-cooled, with a
variable-speed DC fan.
The amplifier shall have circuitry to protect itself and the
speaker load from output short circuits, DC voltage on out-
puts, and thermal overload. The amplifier shall include cir-
cuitry to gradually increase gain to attenuator setting lev-
els when the amplifier is turned on, and circuitry for
impedance sensing and clip limiting.
The amplifier shall have a voltage gain of X40 with an
input sensitivity of 1.2V for rated power at 4 ohms. The
hum and noise level shall be at least 100dB below rated
output, "A" weighted. SMPTE IMD shall be less than
0.1% at rated power, 60Hz and 7kHz. The amplifier shall
have a class AB output stage with a modulated power sup-
ply. The frequency response shall be greater than 20Hz-
20kHz, +0/-0.3dB (1W/8Ω).
The amplifier shall operate at 100-240V, 50-60 Hz AC
(configured at factory). Maximum current draw shall not
exceed 21 amperes at 120VAC, (circuit breaker limited),
with both channels driving continuously into a 4 ohm resis-
tor.
The amplifier front panel shall include Active, Temp/DC,
Signal Present and Clip/Limit LED indicators for each
channel, a combination power switch/magnetic circuit
breaker and recessed and detented gain pots.
Rear panel input connectors shall be actively balanced and
have female XLR-type, 3-pin connectors (pin 3+). Output
connectors shall be 5-way output binding posts. Octal
sockets for optional accessory modules and a
signal/ground lift jumper shall be provided.
A rear-panel AC mains cord having an appropriate AC
plug for the intended operating voltage shall be provided
(market dependent).
The packaging of the amplifier shall allow for standard
rack mounting without requiring space between similar
units. Dimensions shall be 3.5" (89mm) high x 19"
(483mm) wide x 15" (381mm) deep. The amplifier shall
have a net weight of 51.0 lbs. (23.10 kg). The amplifier
shall be designated the Crest Audio Model 6001.
L'HUMIDITÉ
SIGNAL
GROUND
LIFT
USA ONLY
Designed & manufactured in the USA by:
OUTPUT POWER
IN WATTS PER
CHANNEL, 2
600W
720W
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
100 Eisenhower Dr., Paramus NJ 07652 USA
: 201.909.8700
TEL
OUT A
+
BRIDGE
--
OUT B
Crest Audio Inc.
: 201.909.8744
FAX
http://www.crestaudio.com
Printed in USA