Accusplit Eagle AE170XL 운영 지침 - 페이지 2

{카테고리_이름} Accusplit Eagle AE170XL에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Accusplit Eagle AE170XL 4 페이지. Accusplit fitness electronics user manual

페이지 인쇄

SETTING PROCEDURE

ACCUSPLIT products use a common setting procedure

known as "S1- S2-S3-S4. " Here's how it works:

Press S1 for 2 seconds: Enter the SET mode

Press S2: Change the field to be set

Press S3: Change the field value

Press S4 for 2 seconds: Exit the SET mode

You can enter and exit Set mode from any of the regular

display screens. Once in Set mode, you can cycle through all

of these settings by pressing S2 repeatedly:

Set Stride Length g Set Weight g Set Stride Length

"in" indicator

for inches

IGI

ALKER

STEP TIME

DIST

140S

JW200

S3-

Setting Stride Length

Finding Your Stride Length:

length of one of your steps, measured from "toe to toe. " T o

measure, walk 10 steps with your normal stride and measure

the T OTAL DISTANCE from the toe of your starting step to

the toe of your 10th step (see diagram below). Divide the

TOTAL DISTANCE by 10, and multiply the decimal portion by

12 to find your stride length in feet and inches. Example: Y ou

walk 23 feet and 6½ inches in 10 steps. Convert to feet only =

23.542 feet (6½ ÷ 12 = 0.542). Divide by ten to get the stride

length in feet = 2.354 feet. Now, convert back to feet and

inches to get your stride length = 2 feet 4.25 inches (0.354 ×

12 = 4.25).

10 steps

Setting your Weight

1. (Continuing from above) - After pressing S2,

you will see the "in" indicator go out, and the "lb"

indicator come on. T he display will show a flashing

number, which is your Weight setting (in pounds).

Note: Unit will show "kg" for weight setting when in

metric mode.

2. As before, press the S3 + (MODE) button to increase

the Weight (in increments of ½ pound), and press the S3

- (RESET) button to decrease the Weight setting. Hold the

buttons down to change values quickly.

3. Press the S2 button to adjust the Clock.

Stride

.COM

Length

SET

Flashes

S1,S2,S4

S3+

Your stride length is the

We recommend that you adjust the settings all at once, using

the procedure below.

Entering set mode

Press and hold the S1 button for 2 seconds.

The display will start to flash, showing that you've entered

SET mode.

Setting Stride Length

1. Press S2, repeatedly until the mode indicator

bar is underneath DIST and the "in" indicator comes on.

The display will show a flashing number, which is your

Stride Length set point (in inches).

2. Press the S3 + (MODE) button to increase the Stride

Length (in increments of ¼ inch), and press the S3-

(RESET) button to decrease the Stride Length. Hold

the buttons down to change values quickly.

3. Press the S2 button to adjust your weight setting.

IGI

STEP

"lb" to

indicate

pounds

170

JW200

S3-

Setting Your Weight

Note: If you need to go back and change some of the values,

simply press S2 to cycle through all of the set points until you

see the one you want to change.

Exiting Set Mode

Press and hold the S4 button for 2 seconds. T he unit will exit

setting mode – no values will be flashing anymore.

Note: T he unit will save any changes and exit set mode after

30 seconds unattended.

ALKER

.COM

DIST CAL

SET

S1,S2,S4

S3+