Fiap Aqua Active Mini SET 매뉴얼 - 페이지 3

{카테고리_이름} Fiap Aqua Active Mini SET에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fiap Aqua Active Mini SET 19 페이지.

페이지 인쇄

FIAP Aqua Active Mini SET

Information about this operating manual

Please read the operating instructions and familiarise yourself with the unit prior to using it for the first

time. Adhere to the safety information for the correct and safe use of the unit.

Intended use

The FIAP Aqua Active Mini SET series, in the following text termed unit, is exclusively intended for

pumping normal pond water for water features and fountains. Ensure that the unit is only operated at a

water temperature of +4°C to +35°C and at a rated voltage coinciding with the information on the type

plate.

Use other than that intended

Danger to persons can emanate from this unit if it is not used in accordance with the intended use and

in the case of misuse. If used for purposes other than that intended, our warranty and operating permit

will become null and void.

CE Manufacturer's Declaration

We declare conformity in the sense of the EC directive (89/336/EEC) as well as the low voltage

directive (73/23/EEC). The following harmonised standards apply:

EN 60335-1, EN 60335-2-41, EN 55014-2, EN 61000-3-2, EN 61000-3-3

Safety information

For safety reasons, children and young persons under 16 years of age as well as persons who

cannot recognise possible danger or who are not familiar with these operating instructions, are

not permitted to use the unit!

Please keep these operating instructions in a safe place! Also hand over the operating instructions

when passing the unit on to a new owner. Ensure that all work with this unit is only carried out in

accordance with these instructions.

The combination of water and electricity can lead to danger to life and limb, if the unit is incorrectly

connected or misused. Only operate the unit if no persons are in the water! Prior to reaching into the

water, always disconnect the power supply to all units used in the water. Compare the electrical values

of the power supply with those on the type plate on the packaging or on the unit itself. Ensure that the

unit is fused for a rated residual current of max. 30 mA via a residual current-operating system. Only

use cables approved for outside use. Do not carry or pull the unit by the connection cable! The power

connection cable of this unit cannot be replaced. If the cable is damaged, the entire unit has to be

disposed of. Electrical installations at garden ponds must meet the international and national

regulations valid for installers. Never open the unit housing or its attendant components, unless this is

explicitly mentioned in the operating instructions. Never carry out technical changes to the unit. Only

use original spare parts and accessories for the unit. Only allow authorised customer service outlets to

perform repairs. Never run the unit without water! Never use the pump for fluids other than water! For

your own safety, consult a qualified electrician when you have questions or encounter problems!

Assembly and installation

Screw T distributor to the connection socket, screw nozzle tube to the T distributor. Screw nozzle

mounting and the desired water feature nozzle to the nozzle tube. It is possible to connect a hose to

the lateral outlet at the T distributor by means of the reduction element and the stepped hose

connection. Place the unit in the pond horizontally on firm, sludge-free ground and ensure that it is

completely covered with water (at a maximum of 1,3 m below the water level).

Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045

FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen

Tel: 09628 9213 0; Fax: 09628 9213 30;

www.fiap.com

FIAP Aqua Active Mini SET

Start-up

Attention! Never operate the unit without water flowing through!

The unit switches on automatically when connection to power is established. Align the nozzle tube.

The water feature height and the water flow can be adjusted with a regulator at the lateral outlet at the

T distributor. The power supply must be disconnected to switch off the unit.

Cleaning

Attention! Always disconnect the power supply prior to starting cleaning and maintenance

work!

Unscrew the nozzle tube including T distributor and connection socket. Open strainer casing and

remove pump. Unscrew pump lid and remove impeller. Clean all components using clear water and a

brush. After cleaning the pump, reassemble in the reverse order. Route connection cable such that it

cannot be pinched.

Storage/Over-wintering

Remove the unit at temperatures below zero degrees centigrade. Thoroughly clean the unit, check for

damage and store immersed in water in a frost-free environment. Do not immerse the plug!

Wearing parts

The rotor is a wearing part and is, therefore, not covered by our warranty.

Disposal

Dispose of the unit in accordance with the national legal regulations.

Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045

FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen

Tel: 09628 9213 0; Fax: 09628 9213 30;