Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 백서 - 페이지 8

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 백서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지), 설치 참고 사항 (36 페이지)

Both supervisor engines run a synchronizing operation to allow for transfer of this data. When a database entry is updated on

the active supervisor engine, the synchronizing operation places the update in a ﬁrst-in, ﬁrst-out (FIFO) queue. This queue is

scheduled to empty periodically for transfer to the standby supervisor. The transfer is a background process and as such, the

update interval varies depending on the number of other active processes in the system. The update interval ranges from one

to ﬁve seconds with two seconds being an approximate average. The standby supervisor engine's synchronizing process

receives these asynchronous updates and enters them into the protocol state database on the standby supervisor engine. When

the system starts or when a second supervisor engine is hot-inserted, a global synchronization takes place between the protocol

databases to ensure all protocol states are up to date.

Figure 2

Stateful Protocol Database Depiction

To summarize the stateful protocol feature, the high-availability switchover performance is more dependent on the status of

the synchronization procedure than on the complexity of the conﬁguration. After the system and protocols reach a stable

operating point, the protocol state databases on each of the supervisor engines will have a fairly similar status (depending on

updates in the queue). The determining factor for switchover performance is the number of updates in the queue that have not

been completed. The resulting high-availability supervisor engine switchover performance is less than three seconds.

Supervisor Engine Software Image Upgrades

In a redundant supervisor engine conﬁguration, Cisco Catalyst OS images must be properly managed to ensure high

availability of the system. The following section describes some options for managing Cisco Catalyst OS images.

Supervisor Engine Image Synchronization

By default on the Cisco Catalyst 6500 Series, the Cisco Catalyst OS software images on the active and the standby supervisor

engines must be the same. This allows the system to maintain a stable operating environment by ensuring that the supervisor

engine switchover occurs with the same software features and revisions on the new active supervisor engine as on the

previously active supervisor engine. If the two images are not the same version during system bootup, the active supervisor

engine downloads its current boot image to the standby supervisor engine. The NVRAM conﬁguration of the active supervisor

engine is also synchronized between the supervisor engines.

Protocol Database

Active

Supervisor

Data

Packet

Plane

Cisco Systems, Inc.

Page 8 of 19

Protocol Database

Standby

Supervisor