Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 매뉴얼 - 페이지 5

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 설치 참고 사항 (36 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 매뉴얼
Cisco - Connecting a Terminal to the Console Port on Catalyst Switches
Connecting a Terminal to Catalyst 2948G-L3,
4908G-L3, and 4840G Series Switches
You may configure the Catalyst switch routers from a direct console connection to the console port or
remotely through its management port.
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female data terminal equipment (DTE)
adapter (labeled "Terminal") to connect the console port to a PC running terminal emulation
software.
If you are using a direct console connection, configure your terminal emulation program for 9600
baud, 8 data bits, no parity, and 1 stop bit.

Console Port Pinouts

The console port is an RJ-45 receptacle. Data Terminal Ready (DTR) and Data Set Ready (DSR)
handshake signals are supported. The Request To Send (RTS) signal tracks the state of the Clear To Send
(CTS) signal.
Table B-1
Table B-1: Console Port Pinouts
Pin
Signal
Direction
1¹
RTS/CTS Output
2
DTR
Output
3
TxD
Output
4
SGND
5
SGND
6
RxD
Input
7
DSR
Input
8¹
RTS/CTS Input
¹Pin 1 and pin 8 are connected.
Connecting a Terminal to Catalyst 2926 and 2926G
Series Switches
On the Catalyst 2926 series switch, the console port is located on the Supervisor Engine front panel and
is labeled "CONSOLE," as shown in the figure below.
Figure: Console Port Connector (Catalyst 2926 Series Switch)
http://www.cisco.com/warp/public/473/9.html (5 of 19) [9/4/2003 12:36:02 PM]
lists pinouts for the console port.
Description
Request To Send / Clear To
Send
Data Terminal Ready
Transmit Eata
Signal Ground
Signal Ground
Receive Data
Data Set Ready
Request To Send / Clear To
Send