Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항 - 페이지 14

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 36 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항
Removing a CFC or DFC3 Daughter Card
Removing the DFC3 Daughter Card
If your WS-X67xx Ethernet module is equipped with a DFC3 daughter card, you must remove it before
you install the DFC4 daughter card.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
To remove the DFC3 daughter card from modules, follow these steps:
Attach an ESD grounding strap to your wrist and to ground.
Step 1
Remove the Ethernet module from the chassis.
Step 2
If you are unsure about the correct procedure for removing a module from the switch chassis, refer to
the
Place the Ethernet module on an antistatic mat with the front of the module facing toward you.
Step 3
If you are upgrading a WS-X6748-GE-TX Ethernet module with a DFC4 daughter card and your
Step 4
WS-X4748-GE-TX module is equipped with a stiffener bracket that goes across the top of the heat sinks
at the front of the module (see
with the CFC daughter card removal procedure. To remove the bracket, follow these substeps:
a.
b.
Do not reinstall the stiffener bracket. After upgrading the WS-X6748-GE-TX Ethernet module with a
Caution
DFC4 daughter card, the bracket can be discarded.
If your DFC daughter card has a small metal installation bracket as shown in
Step 5
Phillips-head screwdriver to remove the two cap nuts and the one screw securing the bracket. Set them
aside along with the bracket. If there is no bracket, just remove the two cap nuts and the one screw.
Remove the remaining installation hardware. (See
Step 6
Note
Catalyst 6500 Series Distributed Forwarding Card 4 for WS-X68xx, WS-X69xx, and Select WS-X67xx Modules Installation Note
14
"Removing an Ethernet Module from the Chassis" section on page 28
Loosen and remove the six phillips-head screws that secure the bracket to the module.
Carefully lift and remove the bracket from the module.
The installation hardware shown in
installation hardware for a DFC3C or a DFC3CXL daughter card consists of 6 screws, 2 cap nuts,
and 1 standoff.
Figure
1), you must first remove the stiffener bracket before continuing
Figure
Figure 4
is for a DFC3B or DFC3BXL daughter card. The
for removal instructions.
Figure
4.)
4, use a No.1
OL-24918-02