Cisco AJ732A - MDS 9134 Fabric Switch 릴리스 노트 - 페이지 37

{카테고리_이름} Cisco AJ732A - MDS 9134 Fabric Switch에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco AJ732A - MDS 9134 Fabric Switch 44 페이지. Converged network switches for nx-os 4.0(1a)n1(1)
Cisco AJ732A - MDS 9134 Fabric Switch에 대해서도 마찬가지입니다: 구성 매뉴얼 (49 페이지), 릴리스 노트 (48 페이지), 릴리스 노트 (44 페이지), 릴리스 노트 (36 페이지), 릴리스 노트 (26 페이지), 릴리스 노트 (22 페이지), 빠른 참조 매뉴얼 (14 페이지), 릴리스 노트 (3 페이지)

페이지 인쇄
Cisco AJ732A - MDS 9134 Fabric Switch 릴리스 노트
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Note
Workaround: This issue is resolved.
•
CSCso63465
Symptom: FCP-CMD (for example, Inquiry) frames targeted to LUN 0x45F0 or LUN 0x50F0 are
dropped by an MDS switch when traffic flows (egresses) through Generation 2 modules. LUN
0x45F0 corresponds to HPUX Volume Set Address <VBUS ID: 0xB, Target ID: 0xE, LUN: 0x0>.
Workaround: This issue is resolved.
CSCsq54455
•
Symptom: On a DS-X9032 module where the SRAM parity error was seen, the SRAM parity error
exceptions were logged continuously.
Workaround: This issue is resolved.
CSCsq57352
•
Symptom: After upgrading from Fabric Manager Release 3.0(2a) to Fabric Manager
Release 3.2(3a), the Fabric Manager client fails to reuse the map layout files produced by Release
3.0(2a). Renaming the map layout files will make them compatible with Fabric Manager Release
3.2(3a).
Workaround: This issue is resolved.
CSCsq66823
•
Symptom: On an MDS 9222i switch, an upgrade from SAN-OS Release 3.2(x), Release 3.3(1a), or
Release 3.3(1c) to SAN-OS Release 3.3(1c) fails when there is an active FC-Redirect configuration
(created by SME or DMM applications) on the switch. An active FC-Redirect configuration is
defined as:
If an upgrade is attempted when an active configurations is present, the switch will go into a
disruptive upgrade.
Workaround: This issue is resolved.
CSCsr90831
•
In rare instances, the following Generation 2 modules and MDS switches might reload:
OL-14116-11
This applies only to Terminal Server running in Application Mode. This issue does not affect
users running a Terminal Server or Remote Desktop session in Remote Administration
mode.
•
FC-Redirect configuration for hosts or targets connected locally
FC-Redirect configuration created by the application running on that switch.
•
MDS 900012-port 4-Gbps Fibre Channel switching module
•
MDS 9000 24-port 4-Gbps Fibre Channel switching module
•
MDS 9000 48-port 4-Gbps Fibre Channel switching module
•
MDS 9000 4-port 10-Gbps Fibre Channel switching module
•
MDS 9124 Multilayer Fabric Switch
•
Cisco Fabric Switch for HP c-Class BladeSystem
•
Cisco Fabric Switch for IBM BladeCenter
•
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3)
Caveats
37