Cisco AP775A - Nexus Converged Network Switch 5010 릴리스 노트 - 페이지 19
{카테고리_이름} Cisco AP775A - Nexus Converged Network Switch 5010에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco AP775A - Nexus Converged Network Switch 5010 44 페이지. Cisco nexus 5000 series release notes release 4.1(3)n1(1) (ol-16601-01 h0, july 2009)
Cisco AP775A - Nexus Converged Network Switch 5010에 대해서도 마찬가지입니다: 릴리스 노트 (48 페이지), 릴리스 노트 (26 페이지), 빠른 참조 매뉴얼 (14 페이지), 릴리스 노트 (26 페이지)
페이지 인쇄
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.3(3)
Starting with Cisco MDS SAN-OS Release 3.0(1), the SSM front panel ports can no longer be
configured in auto mode, which is the default for releases prior to Release 3.0(1).
Note
To avoid any traffic disruption, modify the configuration of the SSM ports as described below, before
upgrading a SAN-OS software image prior to Release 3.3(3).
For more information on upgrading SAN-OS software, see the
Software Image" section on page 10.
If the configuration is not updated before the upgrade, the installation process for the new image will
automatically convert all ports configured in auto mode to Fx mode. This change in mode might cause
a disruption if the port is currently operating in E mode.
To upgrade the image on your SSM without any traffic disruption, follow these steps:
Step 1
Verify the operational mode for each port on the SSM using the show interface command:
switch# show interface fc 2/1 - 32
fc2/1 is up
Change the configuration for the first port of the quad when the admin port mode is auto. (A quad is a
Step 2
group of four ports, supported by a data path processor (DPP). The groups are 1 to 4, 5 to 8, 9 to 12, and
so on.) Do not leave the port mode set to auto.
Change the configuration for ports 2, 3, and 4 of the quad:
Step 3
OL-14116-11
Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
Port WWN is 20:4b:00:0d:ec:09:3c:00
Admin port mode is auto
snmp traps are enabled
Port mode is F, FCID is 0xef0300
Port vsan is 1
Speed is 2 Gbps
Transmit B2B Credit is 3
Set the port admin mode to E or Fx if the current operational port mode is E, TE, F or FL.
a.
switch# config t
switch(config)# interface fc 2/1
switch(config-if)# switchport mode fx
Set the port admin mode to E if the current operational port mode is E:
b.
switch# config t
switch(config)# interface fc 2/5
switch(config-if)# switchport mode e
Set the admin port mode to Fx if the admin port mode of these ports is E, TE, or auto.
a.
switch# config t
switch(config)# interface fc 2/2
switch(config-if)# switchport mode fx
If the first port in the port group has admin mode E or if the port is operational in E port mode,
b.
change the admin state of ports 2, 3, and 4 to shutdown.
switch# config t
switch(config)# interface fc 2/2
switch(config-if)# shutdown
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3)
Upgrading Your Cisco MDS SAN-OS Software Image
"Upgrading Your Cisco MDS SAN-OS
<-------- shows port is configured in auto mode
<-------- shows current port operational mode is F
19