Cisco AP775A - Nexus Converged Network Switch 5010 릴리스 노트 - 페이지 9

{카테고리_이름} Cisco AP775A - Nexus Converged Network Switch 5010에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco AP775A - Nexus Converged Network Switch 5010 44 페이지. Cisco nexus 5000 series release notes release 4.1(3)n1(1) (ol-16601-01 h0, july 2009)
Cisco AP775A - Nexus Converged Network Switch 5010에 대해서도 마찬가지입니다: 릴리스 노트 (48 페이지), 릴리스 노트 (26 페이지), 빠른 참조 매뉴얼 (14 페이지), 릴리스 노트 (26 페이지)

Cisco AP775A - Nexus Converged Network Switch 5010 릴리스 노트
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
switch#
Mod
---
...
...
5
6
For a Supervisor-2 module, the output might look like this:
switch#
Mod
---
...
...
7
8
Migrating from Supervisor-1 Modules to Supervisor-2 Modules
As of Cisco MDS SAN-OS Release 3.0(1), the Cisco MDS 9509 and 9506 Directors support both
Supervisor-1 and Supervisor-2 modules. Supervisor-1 and Supervisor-2 modules cannot be installed in
the same switch, except during migration. Both the active and standby supervisor modules must be of
the same type, either Supervisor-1 or Supervisor-2 modules. For Cisco MDS 9513 Directors, both
supervisor modules must be Supervisor-2 modules.
Migrating your supervisor modules is a disruptive operation.
Caution
Migrating from Supervisor-2 modules to Supervisor-1 modules is not supported.
Note
To migrate from a Supervisor-1 module to a Supervisor-2 module, refer to the step-by-step instructions
in the
Configuring Generation 2 Switching Modules
The Cisco MDS 9500 Multilayer Directors are designed to operate with any combination of Cisco MDS
9000 Generation 1 and Generation 2 modules. However, there are limitations to consider when
combining the various modules and supervisors in the Cisco MDS 9500 Series platform chassis. The
references listed in this section provide specific information about configurations that combine different
modules and supervisors.
For information on configuring Generation 2 switching modules, refer to the Configuring Generation 2
Switching Modules chapter in the the
For information on port index availability, refer to the "Port Index Availability" section in the Product
Overview chapter of the
For information on Cisco MDS 9000 hardware and software compatibility, refer to the
SAN-OS Hardware and Software Compatibility
OL-14116-11
show module
Ports
Module-Type
-----
-------------------------------- ------------------ ------------
0
Supervisor/Fabric-1
0
Supervisor/Fabric-1
show module
Ports
Module-Type
-----
-------------------------------- ------------------ ------------
0
Supervisor/Fabric-2
0
Supervisor/Fabric-2
Cisco MDS 9000 Family CLI Configuration
Cisco MDS 9500 Series Hardware Installation
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3)
Model
DS-X9530-SF1-K9
DS-X9530-SF1-K9
Model
DS-X9530-SF2-K9
DS-X9530-SF2-K9
Guide.
Cisco MDS 9000 Family CLI Configuration
Information.
Software Download Process
Status
active*
ha-standby
Status
active *
ha-standby
Guide.
Guide.
Cisco MDS 9000
9