FIBARO FGS-222 운영 매뉴얼 - 페이지 3

{카테고리_이름} FIBARO FGS-222에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. FIBARO FGS-222 4 페이지. Double relay switch

페이지 인쇄

TIPS FOR ARRANGING THE ANTENNA:

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

order to prevent interferences.

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door

frames) may impair signal reception!

Do not cut or shorten the antenna - its length is

perfectly matched to the band in which the system

operates.

NOTE

It should be noted that only the push-button

connected to S1 terminal and service push-button

B enables "learning" mode (Include/ Exclude).

DICTIONARY:

• Adding (Inclusion) - Z-Wave device learning mode, allowing to

add the device to existing Z-Wave network.

• Removing (Exclusion) - Z-Wave device learning mode, allowing

to remove the device from existing Z-Wave network.

• Association (linking devices) - direct control of other devices

within the Z-Wave system network.

• Multi-channel association - controlling other multi-channel

devices within the Z-Wave network.

III Activating Double Relay Switch

1. Installing the Double Relay Switch

STEP 1

Connect the device in accordance with the wiring diagram

presented in Figure 1. Switch on the mains voltage.

[Adding/Removing] Double Relay Switch [to/from] Z-wave

network

STEP 2

Double Relay Switch must be placed within the range of Home

Center controller, as adding mode requires direct communication

with the controller.

STEP 3

Find key no. 1 which allows to switch circuit 1 on, in accordance

with the diagram

STEP 4

Set the Home Center controller in add/remove mode (see the

controller's manual)

STEP 5

Add Double Relay Switch to the network by pushing three times key

no. 1 or push-button B located inside the housing of the device. For

toggle switch perform 3 position changes.

During the installation it is recommended to use a

momentary key connected to S1.

STEP 6

The controller indicates when the device is correctly added to the

network, (see the manual of Home Center controller).

CAUTION

Double Relay Switch cancels the "learning" mode

after key no. 1 is pressed once. Therefore, pressing

key no. 1 four times will not add the devices to the

network. The same applies to push-button B.

CAUTION

Double Relay Switch is set by default to operate

with momentary switches (i.e. single-pole switch or

bell switch). While adding Double Relay Switch to

the network with toggle switches, ensure that all

switch contacts are open (off), because closing

them results in activating the push-button and this

will prevent adding the device to the network.

2. Resetting Double Relay Switch

Fibaro Switch provides two methods for resetting.

Method I : Reset by removing Double Relay Switch from the

existing Z-Wave network. The device may be removed using the

controller that has the ability to include/exclude devices from/to

Z-Wave network (see the manual of controller).

Method II : Reset by holding B button for 3 sec. after connecting

mains voltage to the Switch

3. Controlling Double Relay Switch by momentary or

toggle switches.

Momentary switch (after releasing the push-button a spring

automatically pushes back and disconnects the button)

- Turning on/off circuit 1 or 2 - briefly press the push-button

corresponding to a chosen circuit (see diagram).

Toggle switch (operates as a two-position switch, it has no

spring that would push back the device after releasing manual

pressure)

- Turning on/off the circuit - change the position of selected

push-button from the current position.

4. Controlling Double Relay Switch using a

command: ALL ON / ALL OFF

Fibaro Switch responds to commands ALL ON / ALL OFF that may

be sent by the controller. ALL ON / ALL OFF commands are usually

implemented in Z-Wave remote control.

By default, Fibaro Switch accepts both active commands ALL ON

and ALL OFF. Settings may be changed by entering an appropriate

value into configuration register no. 1 (see configuration)

5. Controlling Double Relay Switch using Home

Center controller

After adding Double Fibaro Switch to the network, it will be

represented in Home Center by the following two icons (one icon

represents one channel):

Fig.3 Icons of Double Relay Switch shown by

Home Center controller

Turning on/off the device connected to Double Relay Switch is

performed by pressing ON/OFF icon.

IV Association

Association enables Fibaro Switch to directly control a device

included in Z-Wave network e.g. Dimmer, Switch (ON-OFF), Roller

Shutter or scene (scene may be controlled only through the Home

Center controller).

Association ensures direct transfer of control

commands between devices, and is performed

without participation of the main controller.

Fibaro Switch provides association of three groups.

1st group is assigned to key no. 1

2nd group is assigned to key no. 2

3rd group reports state of devices. Only one device can be

associated to this group.

Fibaro Switch enables user to control up to 5 normal devices, and

5 MultiChannel devices in group no. 1 and no. 2, group no. 3 has

only one field. One field is reserved for the network controller.

To add an association (using the Home Center controller), go to

device options by clicking the following icon:

Select the "device options" tab. Then specify to which group and

what devices are to be associated. Sending relevant information to

devices added to associated groups may take even a few minutes.

WARNING

When Fibaro Switch sends control commands and

a new command is issued, then the current one

command transmission is interrupted to send new

commands.

FGS-222 Fibaro Switch supports the operation of multi-channel

devices. Multichannel devices are devices that include two or more

circuits inside one physical unit.

FGS-222 Double Relay Switch is a multichannel device. It means

that it has two independent executive circuits - each circuit is

recognized by the Home Center controller as a separate device.

Accordingly, each channel is represented by an independent icon.

The first channel is operated by a push-button connected to S1

terminal and it is the main (default) channel.

The association of the second channel of the double relay

switch may be operated only by devices supporting

multi-channel association !

V Configuration

The following settings are available in the Fibaro interface as

simple options that may be chosen by selecting the appropria-

box.

In order to configure Fibaro Switch (using the Home Center

controller), go to device options by clicking the following icon:

Select „Advanced" tab.

Parameter No. 1 - Activate / deactivate functions ALL ON / ALL

OFF.

Default value: 255

Options for changing parameter 255, 0, 1, 2

Available configuration parameters:

255 - ALL ON active, ALL OFF active.

0 - ALL ON is not active ALL OFF is not active

1 - ALL ON is not active ALL OFF active

2 - ALL ON active ALL OFF is not active

Parameter No. 3 - Auto off relay after specified time, with the

possibility of manual override - immediate Off after button

push.

Default value: 0

Available settings:

0 - manual override disabled. After single button push the relay turns

on and automatically turns off after specified time.

1 - manual override enabled. After single button push the relay turns

on and automatically turns off after specified time. Another button

push turns the relay off immediately.

Parameter No. 4 - Auto off for relay 1.

Default value: 0

Available settings:

[1 - 65535] (0,1 s – 6553,5 s) Time period for auto off, in miliseconds

0 - Auto off disabled

Parameter No. 5 - Auto off for relay 2.

Default value: 0

Available settings::

[1 - 65535] (0,1 s – 6553,5 s) Time period for auto off, in miliseconds

0 - Auto off disabled

Parameter No. 6 - Sending commands to control devices

assigned to 1-st association group (key no. 1).

Default value: 0

Available configuration parameters:

0 - commands are sent when device is turned on and off

1 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command, dimmers memorize the last saved state (e.g. 50%

brightness).

2 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command and dimmers are set to 100% brightness.

NOTE: Parameter 15 value must be set to 1 to work properly.

This activates the double-click functionality - dimmer/roller

shutter control.

Parameter No. 7 – Sending commands to control

assigned to 2-nd association group (key no. 2).

Default value: 0

Available configuration parameters:

0 - commands are sent when device is turned on and off

1 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command, dimmers memorize the last saved state (e.g. 50%)

2 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command and dimmers are set to 100% brightness.

Info: Parameter 15 must be set to 1 to make this parameter work

properly. This activates the double-click functionality - dimmer/roller

shutter control.

Parameter No. 13 - Assigns bistable key status to the device

status.

Default value: 0

Available configuration parameters:

0 - [On / Off] device changes status on key status change.

1 - Device status depends on key status: ON when the key is ON,

OFF when the key is OFF.

Remote control from Fibaro System is still

possible. This function is useful when you want

display status of external devices, e.g. Motion

Sensor, in Fibaro System.

devices