Crestron Mercury CCS-UC-1 매뉴얼에서
{카테고리_이름} Crestron Mercury CCS-UC-1에 대한 매뉴얼에서을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron Mercury CCS-UC-1 2 페이지. Tabletop conference system
Crestron Mercury CCS-UC-1에 대해서도 마찬가지입니다: 빠른 시작 (2 페이지), 빠른 시작 매뉴얼 (9 페이지), 매뉴얼에서 (2 페이지)
페이지 인쇄
DO
GUIDE
CCS-UC-1
Crestron Mercury™ Tabletop Conference System
DO
Install the Cable Retention Plate
Install the cable retention plate as shown in the following diagram. The cable retention plate is designed to fit at the cable exit location at the rear of the
Crestron Mercury chassis and provides three tie-down points for cables connected to the device.
NOTE:
If the CCS-UCA-SMK swivel mount kit is to be used, use the cable retention bracket included with the CCS-UCA-SMK. For details, refer to the
CCS-UCA-SMK DO Guide (Doc. 7882) at www.crestron.com/manuals.
Install cable
retention
plate here
CAUTION:
When turning over the device, place the device on a soft surface to avoid damage to the unit.
NOTE:
Allow the cable retention plate adhesive to properly cure before attaching any wiring.
DO
Connect the Device
The Crestron Mercury device should be wired for its intended use. Refer to the following table to determine what is necessary for the specific installation.
REQUIRED WIRING
GENERAL
WIRING
Route cables through swivel tube plate
No
Service Loops
Yes
Cable Retention Plate
Yes
Feed Cables Through the Swivel Tube Plate (Installations with CCS-UCA-SMK only)
If the CCS-UCA-SMK swivel mount kit is used in the installation, refer to the CCS-UCA-SMK DO Guide (Doc. 7882) at www.crestron.com/manuals.
NOTE:
If the 6' HDMI input cable and the 6' USB cable are to be routed to the front of the Crestron Mercury device, do not route the cables through the
swivel tube plate.
Hardware Hookup
When wiring the Crestron Mercury device to external devices, it is highly recommended to use the cables that ship with the Crestron Mercury
device. Each kit ships with every cable needed for most rooms. The cables and accessories have been designed so that a service loop can be
implemented prior to the cables leaving the Mercury's chassis body (if necessary). If an extension option is required, Crestron solutions should
always be used and can be found under the MODELS & ACCESSORIES tab at www.crestron.com/products/model/CCS-UC-1.
Cable retention
plate installed
SCENARIO
WIRING WITH SMK
ZOOM ROOM
Yes
Optional
No
Yes
Yes
Yes
DO
Check the Box
QUANTITY
PRODUCT
1
Cable, RJ-45 Male - RJ-45 Male, 12' (3.66 m)
1
Cable, USB 2.0, A - micro B, 6' (1.83 m)
1
Retention Plate, Cable
3
Tie Wrap
CCS-UC-1 W/PS KIT Only
1
Power Pack, PW-2420RU
CCS-UC-1-AV W/PS KIT Only
1
Cable, HDMI, 6' (1.83 m), Thin
1
Cable, HDMI, 20' (6.10 m)
1
Cable, USB 2.0, A Female - A, 15' (4.57 m)
1
Camera, CCS-CAM-USB-F-100
1
IR Emitter Probe, STIRP
1
Power Pack, PW-2420RU
Standard Hookup
Display device
via 20' (6.10 m) HDMI
cable and IR or serial control
®
(CCS-UC-1-AV W/PS KIT only)
Ground
Corporate
network
or PoE+
N
L A
AUX:
10BASE-T/100BASE-TX
Ethernet to SIP or AirMedia
router
®
Zoom Room Hookup
USB B
To USB port on Zoom room
PC via included USB cable
Ground
N
L A
Laptop
via included USB cable and 6' (1.83 m) and HDMI cable
(CCS-UC-1-AV W/PS KIT only)
USB/ACC:
For future use
24 Vdc, 2.5 A
AC power pack
(CCS-UC-1 W/PS KIT and
CCS-UC-1-AV W/PS KIT only)
CCS-UCA-MIC Microphone pods
(sold separately)
CCS-CAM-USB-F-100
Must connect AC power pack to CCS-UC-1
(CCS-UC-1-AV W/PS KIT only)
USB/ACC
Insert included USB stick
here.
24 Vdc, 2.5 A
AC power pack
(CCS-UC-1 W/PS KIT and
CCS-UC-1-AV W/PS KIT only)
CCS-UCA-MIC Microphone pods
(sold separately)
Must connect AC power pack to CCS-UC-1
PART NUMBER
2033988
2047803
2047908
2047935
6500187
6508218
6503567
6508260
6506442
6500940
6500187
100-240 V
50/60 Hz:
From ac power outlet
100-240 V
50/60 Hz:
From ac power outlet