Sharp Carousel R-1500 요리 매뉴얼 - 페이지 6

{카테고리_이름} Sharp Carousel R-1500에 대한 요리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Carousel R-1500 40 페이지. Over the range models
Sharp Carousel R-1500에 대해서도 마찬가지입니다: 요리 매뉴얼 (40 페이지), 서비스 매뉴얼 (44 페이지)

페이지 인쇄

U N P A C K I N G A N D I N S T A L L A T I O N I N S T R U C T I O N S

UNPACKING AND EXAMINING YOUR OVEN

Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest

on plasticfoam pad. Lift carton off oven and remove all packing materials, WALL and

TOP CABINET TEMPLATE, Turntable, and Turntable Support. SAVE THE CARTON

AS IT MAY MAKE INSTALLATION EASIER.

1. Remove the feature sticker from the outside of the door, if there is one.

2. DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the right side

wall of the oven cavity. Check to see that there is a WALL TEMPLATE and TOP

CABINET TEMPLATE. Read enclosures and SAVE the Operation Manual.

Check the oven for any damage, such as misaligned or bent door, damaged door

seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If

there is any damage, do not operate the oven and contact your dealer or SHARP AUTHORIZED SERVICER. See

Installation Instructions for more details.

Please read all instructions thoroughly before installing the Over the Range Microwave Oven/Hood

System. Two people are recommended to install this product.

If a new electrical outlet is required, its installation should be completed by a qualified electrician

before the Microwave Oven/Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on

page 7.

1 MOUNTING SPACE

This Microwave Oven/Hood requires a mounting space on

a wall as shown in Figure 1. It is designed to be used with

standard 12-inch wall cabinets.

If the space between the wall cabinets is 36 or 42 inches, a

Filler Panel Kit can be used to fill the gap. The metal filler

panels come in 3-inch wide pairs. One set is needed for a

36-inch opening and 2 sets for a 42-inch opening. See page

15 for ordering information. The Filler Panel Kit should be

installed before the Microwave Oven/Hood is installed.

2 WALL CONSTRUCTION

This Microwave Oven/Hood should be mounted against and supported by a flat vertical wall. The wall must be flat

for proper installation. If the wall is not flat, use spacers to fill in the gaps. Wall construction should be a minimum of

2" x 4" wood studding and 3/8" or more thick dry wall or plaster/lath. The mounting surfaces must be capable of

supporting weight of 110 pounds—the oven and contents—AND the weight of all items which would normally be

stored in the top cabinet above the unit.

The unit should be attached to a minimum of one 2" x 4" wall stud.

To find the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the nails in the stud.

B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then

placing a mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either

side of this mark.

Downloaded from

www.Manualslib.com

manuals search engine

12"

15.5"

At least 2"

Backsplash

Figure 1

30"

30" or more from

cooking surface

66" or more

from floor