Crestron UC-SB1-CAM 빠른 시작 매뉴얼

{카테고리_이름} Crestron UC-SB1-CAM에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron UC-SB1-CAM 2 페이지. Uc video conference smart soundbar & camera
Crestron UC-SB1-CAM에 대해서도 마찬가지입니다: 빠른 시작 (2 페이지), 빠른 시작 (2 페이지), 시작하기 (10 페이지)

페이지 인쇄
Crestron UC-SB1-CAM 빠른 시작 매뉴얼
UC-SB1 and UC-SB1-CAM
UC Video Conference Smart Sound Bars
Crestron® UC Video Conference Smart Sound Bars (UC-SB1 and UC-SB1-CAM) facilitate conferencing in small to medium-sized meeting spaces
with a built-in microphone, speakers, and camera (UC-SB1-CAM only).
NOTE:
With the exception of the integrated camera, the UC-SB1 and UC-SB1-CAM have similar features. For simplicity within this guide, the term
"sound bar" is used for both models except where noted.
Check the Box
Item
UC-SB1 and UC-SB1-CAM
Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (P/N 2052565)
Cable, USB 3.0, A - B, 6 ft (1.83 m) (P/N 2053077)
Foot, 2.3 in. x 0.96 in. x 0.15 in., Rubber (P/N 2052169)
Key, Anchor (P/N 4529654)
Power Cord (P/N 2052498)
Screw, 8-AB x 1-1/2 in., Pan Head, Combo (P/N 2052567)
Template, Overlay (P/N 4529513)
Install the Sound Bar
The sound bar can be placed on a flat surface or mounted on a wall. The sound bar has the following dimensions:
Dimensions (UC-SB1-CAM shown)
3.90 in.
(99 mm)
43.60 in.
(1107 mm)
Place on a Flat Surface
If placing the sound bar on a flat surface, attach the included rubber feet to the bottom of the sound bar as shown in the following diagram.
Attach Rubber Feet (UC-SB1 shown)
Attach feet here
Qty
1
4
1
2
1
1
4
1
4.57 in.
(116 mm)
Mount on a Wall
The sound bar includes anchors that are suitable for use on sheetrock walls up to 1/2 in. thickness. Masonry and other materials may require
additional installer-supplied mounting hardware.
NOTE:
When mounting on a wall beneath a display device, leave 3/4 in. (minimum) clearance above the top of the sound bar. Use the included
template to allow for sufficient clearance between the sound bar and display device.
The following tools are required to mount the sound bar:
•
Drywall saw (not included)
•
Drill with 5/16 in. bit (not included)
To mount the sound bar on a wall:
1.
The included template provides drill hole locations for the wall mount hardware. Using the center reference hole of the template as a guide,
attach the template to the desired mounting location with the center reference line of the template at the center of the desired location.
NOTE:
The cutout in the center of the template should provide adequate access for all of the required cabling.
Drill one of these two holes
Cutout for sound bar cables
Drill one of these two holes
2.
Drill two pilot holes on each side of the center line as shown in the diagram above. Each side should have one pilot hole drilled in each row of
the template.
3.
Use a drywall saw to make a cutout for the sound bar cables.
4.
Install the four included anchors into the drilled pilot holes.
a.
Fold the anchor in the middle and pinch the ends together.
b.
Insert the anchor in the hole and tap flush with the wall.
c.
Insert the included anchor key to pop the anchor open and lock
it behind a hollow wall.
WARNING:
Do not force or hammer the key.
Drill one of these two holes
Drill one of these two holes
d.
Drive the screw part of the way into the anchor, leaving
approximately 1/4 inch of the screw exposed.
e.
Repeat steps a through d for the other 3 anchors.