Crestron 6506188 빠른 시작 매뉴얼
{카테고리_이름} Crestron 6506188에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron 6506188 3 페이지. Cable retractors for fliptops
페이지 인쇄
CBLR Series
Crestron
®
cable retractors provide a
convenient cable management solution
for use with most Crestron FlipTops™.
This solution allows a user to simply
reach into the FlipTop™ compartment
and pull out any cable to the desired
length. Each cable can be pulled out up
to 3 feet (0.9 meter). A simple press of
the easy-access lever retracts the cable
back into the compartment.
Each Crestron cable retractor features a patent-pending mechanism that dampens the rate of retrac-
tion to prevent the cable from whipping as it is pulled back into the FlipTop storage compartment. The
retraction speed is installer adjustable to ensure full and effortless retraction without excessive force.
Up to three or four cable retractors can be installed depending on the FlipTop model. Blank inserts
(CBLRA-INSERT-BLANK*) are required to fill any unused positions. As an alternative to a blank insert,
a 2-wire insert (CBLRA-INSERT-2WIRE* or FTA-CBLRA-INSERT-2WIRE-102*) is also offered to
accommodate additional non-retracting cables if needed.
1
Preparation
Preparation consists of:
•
Modifying the FlipTop assembly to accommodate the cable retractors.
•
Determining the desired mounting orientation. (Retractors are shipped configured for
horizontal orientation, but are easily reconfigured for vertical orientation.)
NOTE: For preparation of FlipTop 600 Series models, refer to "Modify the FlipTop
(FlipTop 600 Series)" in the third column on this page.
Modify the FlipTop (Non-FlipTop 600 Series)
1.
Remove four screws A to detach
the lower bar assembly. Also remove
two screws B. Retain screws A and B
to attach the FlipTop mounting bracket
assembly. Refer to the FlipTop mounting
brackets table provided in section
to
ensure that the mounting bracket received is
appropriate for the FlipTop being modified.
2.
Remove four screws C to remove the
cable guide. Retain the screws to
attach the two side filler plates*.
3.
Move the mounting bracket assembly
up into position and secure using four
screws A and two screws B.
4.
Place the side filler plates in position
and secure using four screws C.
* Item(s) sold separately.
1
For regulatory compliance information, refer to Doc. 7475.
QUICKSTART DOC. 7245C (2032356, Sheet 1 of 2)
Cable Retractors for FlipTops™
Attachment of Mounting Bracket
Assembly and Side Filler Plates
Mounting Bracket Assembly Installed
Removing Cable Guide and Lower Bar Assembly
Screws C
Cable
Guide
Screw B
Side Filler Plates Installed
Screws A
Screw B
Lower Bar
Assembly
www.crestron.com
02.14
Specifications subject to
change without notice.
Modify the FlipTop (FlipTop 600 Series)
Retractors can be installed in both the left and right sides of the FlipTop 600 Series models.
1.
Screws C
2.
Side Filler
3.
Plates
Screw B
Screws A
Mounting
Screw B
Bracket
Assembly
Reconfigure Retractors for Vertical Operation
To reconfigure the retractors for vertical orientation, refer to the illustration below and do the following:
1.
2.
Mounting
Bracket
Assembly
Side Filler
Plates
888.273.7876
201.767.3400
Remove the screw holding the cable guide in place, then remove the cable guide.
Remove the screws holding the cable pass-through bracket in place, then remove the cable
pass-through bracket.
Remove the shoulder screws from the front of the unit.
Save these as they are used in retractor installation.
Cable Guide
Cable Pass-Through Bracket
Shoulder Screws
Remove the two screws D, one from each side of the retractor, attaching the neck in the horizontal
orientation.
Reposition the neck as shown in the vertical orientation view and attach using the two screws D
plus a third screw E (1/4 in, 6-32, flathead, supplied) to secure the neck in that position.
Horizontal Orientation
Vertical Orientation
Retractor
Neck
Side View
Side View
(2) Screws D
Reverse Side
(One on Each Side)
Retractor
Neck
(2) Screws D
(1) Supplied Screw