Sharp Aquos LC 20S4U 운영 매뉴얼 - 페이지 19
{카테고리_이름} Sharp Aquos LC 20S4U에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC 20S4U 45 페이지. Sharp operation manual liquid crystal television lc-20s4u
Sharp Aquos LC 20S4U에 대해서도 마찬가지입니다: 운영 매뉴얼 (43 페이지)
페이지 인쇄
Basic Operation (Continued)
You can select channels using Channel Select or
CH (A)/{V).
CD CD CD
CD CD CD
CD CD CD
.CD~
AUDIO
MUTE
ONLY
CC
INPUT
(1)000
PIC.FLlP DISPLAY AV MODE
0 0 0
o
~
0
MENU8e8
RON
~
MOU
• To adjust the volume
•
Press VOL (+) to increase the sound volume.
The bar indicator shifts right.
• This LCD TV set allows you to select up to 125 channels
(1 to 125). To select a channel, enter a 2- or 3-digit number.
VOLUME
50 11111111111111111111111111111111111111111111111111··········
•
Press VOL (-) to decrease the sound volume.
The bar indicator shifts left.
• Using Channel Select
When selecting the channel using Channel Select, complete
input of the channel number by holding down the button for
the last digit for a moment.
VOLUME
10 1111111111············································••••••
To select a 1- or 2-digit channel number (e.g., Channel 5):
Complete the following procedure within 4 seconds.
~
• When selecting a 1-digit channel number, do not fail to press the
o
button first.
• To mute the sound
•
Press MUTE to temporarily turn off the sound.
The MUTE mark
[J~
is displayed for
4
seconds.
I
n~
Press the
CD
button.
Press the
CD
button.
To select a 3-digit channel number (e.g., Channel 115):
Complete the following procedure within 4 seconds.
•
Press MUTE or VOL (+)/{-) to turn the sound back to the
previous level.
The mute function is automatically turned off when any of
the following buttons are pressed: POWER, MUTE,
VOL (+)/{-) or MTS.
VOLUME
10 1111111111············································••••••
~
• When VOL (+)/(-) is pressed in the Mute mode, the sound turns
on and the volume indicator is displayed.
• The Mute function is canceled when POWER is pressed.
Press the
~
button.
Press the
CD
button.
115
1
Press the
CD
button.
• To select MTS (Multichannel TV Sound)
Press MTS to display the MTS screen.
Press MTS to select the MTS settings.
STEREO: stereo audio
SAP:
secondary audio program
MONO:
monophonic audio
~
STEREO <ON AIR
SAP
<ON AI R
MONO
I
NOTE
>
• "ON AIR" appears when a STEREO or SAP broadcast is being
aired.
~
• The 3-digit channel number can be selected only when the
receiving mode is set to CABLE in CH-SETTING. (For details on
setting the receiving mode, see page 24.)
Changing channels with CH (A)/(V) on the remote control
Air:
Press CH (A) and the channels change in the order shown below:
2
~
3
~
...
~
68
~
69
~
2
~
3
~
...
Press CH (v) and the channels change in the order shown below:
3
~
2
~
69
~
68
~
...
~
3
~
2
~
...
Cable: Press CH (A) and the channels change in the order shown below:
1
~
2
~
3
~
...
~
125
~1 ~
2
~
3
~
...
Press CH (v) and the channels change in the order shown below:
3
~
2
~
1
~
125
~
...
~
3
~
2
~
1
~
...
• Using FLASHBACK
•
Press FLASHBACK to switch the currently tuned channel
to the previously tuned channel.
•
Press FLASHBACK again to switch back to the currently
tuned channel.
18
@