Sharp AQUOS LC-32SB24U 운영 매뉴얼 - 페이지 13
{카테고리_이름} Sharp AQUOS LC-32SB24U에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp AQUOS LC-32SB24U 33 페이지. Lcd color television
Sharp AQUOS LC-32SB24U에 대해서도 마찬가지입니다: 운영 매뉴얼 (33 페이지), 사용자 설명서 (32 페이지), 서비스 매뉴얼 (10 페이지)
페이지 인쇄
Direct Button Operation
Changing Channels
You can change channels by pressing CH
• (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5
ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1
1
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2
2
•
When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
•
When you enter 0–9 only, channel selection will be made if
there is no operation within a few seconds.
•
If you push "0" by itself, nothing will happen.
•
Complete the above steps within a few seconds.
•
When you enter 0–9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
Changing Volume
You can change the volume by pressing VOLk/l on
the TV or on the remote control unit.
•
To increase the volume, press VOL
•
To decrease the volume, press VOL
Audio status
Output device
Speaker
Variable sound
•
When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
•
See page 25 for details on the Output Select function.
r/s
5
ENT.
• (DOT)
1
ENT.
k
.
l
.
20
Output Select
Fixed
Variable
Mute
60
MUTE
Mutes the current sound output.
Press MUTE.
•
"
" will be displayed on the screen for 30 minutes, and
the sound is silenced.
•
Within 30 minutes of pressing MUTE, mute can be
canceled by using one of the methods below.
- Mute will be canceled if you press VOL
•
Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Sleep Timer
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
•
The remaining time displays when the sleep timer has been set.
•
Each time you press SLEEP, the remaining time switches
as shown below.
Off
30
•
When set, the time automatically starts counting down.
•
If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
•
Five minutes before the time expires, the remaining time
or 0–9,
displays every minute.
•
Select "Off" by pressing SLEEP to cancel the sleep timer.
•
The TV will enter standby when the remaining time reaches zero.
•
When the sleep timer is set, its indicator on the TV lights red.
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
•
A moving image is captured.
•
Press FREEZE again to cancel the function.
•
When this function is not available, "No displaying still
image available." will display.
•
The still image automatically goes out after 30 minutes.
•
If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
INPUT
To view external source images, select the input source
using INPUT on the remote control unit or on the TV.
1
Press INPUT.
•
A list of selectable sources appears.
Press INPUT again or press a/b to select the
2
input source.
•
An image from the selected source automatically displays.
•
Each time INPUT is pressed, the input source toggles.
•
If the corresponding input is not plugged in, you cannot change
the input. Be sure to connect the equipment beforehand.
•
See page 11 for external equipment connection.
•
Press PC to switch to an image from the PC.
13
60
90
120
k/l
or MUTE.