Sharp CD-SW440N 운영 매뉴얼 - 페이지 14

{카테고리_이름} Sharp CD-SW440N에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp CD-SW440N 17 페이지. Sharp mini component system operation manual

페이지 인쇄

Enhancing your system

The connection cord is not included. Purchase a

commercially available cord as shown below.

Portable audio

player, etc.

Audio cable

(not supplied)

AUDIO IN

PHONES

Listening to the playback sounds of

portable audio player, etc.

Use a connection cord to connect the portable audio

player etc. to the AUDIO IN jack. When using video

equipment, connect the audio output to this unit and

the video output to a television.

Press the ON/STAND-BY button to turn the power on.

Press the AUDIO IN button on the remote control or

FUNCTION button repeatedly on main unit to select

AUDIO IN function.

Play the connected equipment. If volume level of the

connected device is too high, sound distortion may

occur. Should this happen, lower the volume of the

connected device. If volume level is too low, increase

the volume of the connected device.

Note:

To prevent noise interference, place the unit away from the

television.

Headphones

● Do not turn the volume on to full at switch on and listen

to music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

● Before plugging in or unplugging the headphones,

reduce the volume.

● Be sure your headphones have a 1/8" (3.5 mm)

diameter plug and impedance between 16 and 50

ohms. The recommended impedance is 32 ohms.

● Plugging in the headphones disconnects the speakers

automatically. Adjust the volume using the VOLUME

control.

MINI C OMPON ENT SY STE M

CD-SW440

FUNCTION

POWER

ON/STAND-BY

VOL

PUSH

OPEN

AUDIO IN

PHONES

E-13

Troubleshooting chart

Many potential problems can be resolved by the owner

without calling a service technician.

If something is wrong with this product, check the following

before calling your authorized SHARP dealer or service

center.

General

Symptom

● The clock is not set

to the correct time.

● When a button is

pressed, the unit

does not respond.

● No sound is heard.

CD player

Symptom

● Playback does not

start.

● Playback stops in

the middle or is not

performed properly.

● Playback sounds

are skipped, or

stopped in the

middle of a track.

Remote control

Symptom

● The remote control

does not operate.

Cassette deck

Symptom

● Sound skipping.

● Cannot hear treble.

● Sound Fluctuation.

● Cannot remove the

tape.

Possible cause

● Did a power failure occur?

Reset the clock. (Refer page

11)

● Set the unit to the power

stand-by mode and then turn

it back on.

● If the unit still malfunctions,

reset it. (Refer page 14)

● Is the volume level set to

"0"?

● Are the headphones

connected?

● Are the speaker wires

disconnected?

Possible cause

● Is the disc loaded upside

down?

● Does the disc satisfy the

standards?

● Is the disc distorted or

scratched?

● Is the unit located near

excessive vibrations?

● Is the disc very dirty?

● Has condensation formed

inside the unit?

Possible cause

● Is the AC power cord of the

unit plugged in?

● Is the battery polarity

correct?

● Are the batteries dead?

● Is the distance or angle

incorrect?

● Does the remote control

sensor receive strong light?

Possible cause

● Is there any slack?

● Is the tape stretched?

● Are the capstans, pinch

rollers or heads dirty?

● If a power failure occurs

during playback, the heads

remain engaged with the

tape. Do not open the

compartment with great

force.