Sharp AR-C260 주요 운영자 매뉴얼 - 페이지 15
{카테고리_이름} Sharp AR-C260에 대한 주요 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp AR-C260 19 페이지. Color adjustment
Sharp AR-C260에 대해서도 마찬가지입니다: 네트워크 스캐너 운영 (42 페이지), 프린터 사용 설명서 (50 페이지), 소프트웨어 설치 매뉴얼 (25 페이지), 컬러 관리 매뉴얼 (8 페이지), 설치 매뉴얼 (15 페이지), 사용자 설명서 (8 페이지)
![Sharp AR-C260 주요 운영자 매뉴얼](/uploads/products/server2/5048383/5048383.png)
PROGRAMS FOR COPY MODE
The key operator programs that are used for copy mode are explained in the following.
I Copy settings
OTHER FUNCTION SETTINGS
Initial status settings
The copier settings will be reset when the main
switch is turned off, when the [CA] key is pressed,
or when the auto clear interval has elapsed. Use
this program to establish new initial settings or to
return the initial settings to the factory default
settings. Paper tray, exposure mode, copy ratio,
duplex mode, and output mode default settings can
be selected.
NOTE
Even if the default state of the two-sided function
has been set to other than one-sided to one-sided
copy mode using this program, in the event that the
two-sided function of the optional duplex module/2
x 500 sheet paper drawer or the reversing
automatic document feeder has failed or has been
prohibited* from use, the default state will revert to
one-sided to one-sided copy mode.
* Disabling of document feeder (page 9)
Disabling of duplex (page 9)
Disabling of inverter (page 9)
Disabling of optional paper drawer (page 9)
Exposure adjustment
Use this program to lighten or darken copies in the
automatic exposure mode. The factory setting is
"5". "1" indicates lighter density and "9" indicates
darker density on the touch panel.
Rotation copy setting
If this program is set, the image of originals will
rotate when the orientation of the originals does not
match that of the copy paper.
(Rotation copy will function only if the auto paper
select or auto image mode has been selected.)
NOTE
For copying from A5 or 5-1/2" x 8-1/2" size originals
onto A5R or 5-1/2" x 8-1/2"R paper, this program
must be set.
Add or change extra preset ratios
Two extra preset copy ratios can be added within
both the reduction range (45% to 99%) and the
enlargement range (101% to 400%). Only added
preset copy ratios can be changed. The standard
preset copy ratios are fixed in memory and cannot
be changed.
Initial margin shift setting
Set the initial margin shift value with this program.
The value can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
If an optional duplex module/2 x 500 sheet paper
drawer (AR-D19) and duplex bypass/inverter unit
(AR-RB1) are not installed, the value for the
reverse side (side 2) is not displayed.
Erase width adjustment
Set the initial setting of the amount of the erase
area with this program.
The values can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
Setting a maximum number of copies
Use this program to limit the maximum number of
copies per copy run which can be input in the copy
quantity display.
A number from 1 to 999 can be set.
13