Sharp AR-C260M 프린터 사용 설명서 - 페이지 40

{카테고리_이름} Sharp AR-C260M에 대한 프린터 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp AR-C260M 50 페이지. Color adjustment
Sharp AR-C260M에 대해서도 마찬가지입니다: 네트워크 스캐너 운영 (42 페이지), 주요 운영자 매뉴얼 (19 페이지), 소프트웨어 설치 매뉴얼 (25 페이지), 컬러 관리 매뉴얼 (8 페이지), 설치 매뉴얼 (15 페이지), 사용자 설명서 (8 페이지)

페이지 인쇄

DESCRIPTION OF SETTING PROGRAMS

Interface settings

These programs are used to control data transmitted to

the parallel port or network port of this printer.

I I I I Port switching method

The machine can use the three ports shown below for

printing. This program is used to select when switching

between ports will take place. "SWITCH AT END OF

JOB" or "SWITCH AFTER I/O TIMEOUT" can be

selected. When "SWITCH AT END OF JOB" is

selected, the port will be automatically selected after

each print job is completed. When "SWITCH AFTER I/

O TIMEOUT" is selected, the port will be automatically

selected if the time set in the I/O Timeout program

elapses.

G Parallel port

G USB port

G Network port

I I I I Enable parallel port

This program is used to enable or disable printing from

the parallel port.

Default setting: Enable

I I I I Enable USB port

This program is used to enable or disable printing from

the USB port.

Default setting: Enable

I I I I Enable network port

This program is used to enable or disable printing from

the network port.

Default setting: Enable

I I I I I/O timeout

This program is used to set the length of time to wait for

an I/O to complete a job on the parallel port or the

network port. If the data stream to the port does not

transmit data for a length of time exceeding the

timeout, the job will cancel and the next job will start

processing.

The I/O timeout setting is used to set the amount of time

after which an I/O timeout will occur when waiting for

print data.

Default setting: 20 seconds

NOTE

The allowable range of the time is 1 to 999 seconds.

TABLE OF CONTENTS

Network settings

These programs are set when this product is used as a

network printer.

After you complete the setting for one program, you

must exit the key operator programs, turn off the main

switch, wait briefly, and then turn on the main switch

again before any other programs can be set. The

program that was set will be effective after the power is

turned on.

NOTE

For setting and modification of "Network settings",

be sure to consult with the network administrator.

I I I I IP address setting

When using this product in a network that uses the

TCP/IP protocol, use this program to set the IP address

(IP address, IP subnet mask, and IP gateway) of this

product. The program is set to ENABLE DHCP by

factory default setting, which obtains the IP address

setting automatically. When using this product on a

TCP/IP network, be sure to turn on the "Enable TCP/

IP" program below.

If DHCP is used, the IP address assigned to the

machine may be changed automatically on occasion.

If this happens, printing will not be possible.

I I I I Enable TCP/IP

When using this product in a network that uses the

TCP/IP protocol, set this program. Also set the IP

address using the program "IP address setting" above.

Default setting: Enable

I I I I Enable NetWare

When using this product in a network that uses the

NetWare protocol, set this program.

Default setting: Enable

I I I I Enable NetBEUI

When using this product in a network that uses the

NetBEUI protocol, set this program.

Default setting: Enable

I I I I Reset the NIC

This program is used to reset all setting items of NIC

(Network Interface Card, namely Print Server Card) of

this product to the factory default settings.

NOTE

If any of the [NETWORK SETTINGS] were changed

prior to execution of this program, you must turn off

the main switch after exiting the key operator

program, wait briefly, and then turn on the main

switch to make the factory default settings take

effect.

BEGINNING OF CHAPTER

6-6