Sharp AR-M620N 주요 운영자 매뉴얼 - 페이지 13

{카테고리_이름} Sharp AR-M620N에 대한 주요 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp AR-M620N 20 페이지. Digital multifunctional system

페이지 인쇄

Disabling of clock adjustment

This program is used to prohibit changes to the clock

adjust setting. When the program is enabled, "Clock" in

the custom settings cannot be used. To adjust the date

and time, this program must first be disabled (remove

the checkmark).

Device control

Use these programs when a peripheral device on the

machine has failed or when you wish to temporarily

disable a device. The programs can also be used to

change the function setting of a device as required by

your conditions of use.

"Device control" consists of the following programs:

G Original size detector setting

G Disabling of document feeder

G Disabling of duplex

G Disabling of large capacity cassette

G Disabling of stapler

G Disabling of punch

G Disabling of finisher

G Disabling of inserter

G Disabling of covers/inserts mode

G Saddle stitch position adjust

G Auto switching of finisher trays

G Rotated output

G Auto paper selection setting

Original size detector setting

This program is used to select the standard original

sizes that can be detected by the original size detection

function. Select one of the four groups indicated below.

The factory default setting is "AB-1 (INCH-1)". Original

size detection by the document glass can also be

disabled.

Detectable original sizes

Document feeder tray (for reversing

Group

automatic document feeding)

Document glass

11" x 17", 8-1/2" x 14",

8-1/2" x 11",

1 INCH-1

8-1/2" x 11"R,

5-1/2" x 8-1/2"

11" x 17", 8-1/2" x 13",

8-1/2" x 11",

2 INCH-2

8-1/2" x 11"R,

5-1/2" x 8-1/2"

A3, A4, A4R, A5,

3 AB-1

B4, B5, B5R

A3, A4, A4R, A5,

4 AB-2

B5, B5R, 216x330

8-1/2" x 11",

216x330

8-1/2" x 11", B4

If "CANCEL DETECTION AT DOCUMENT GLASS" is

set, originals will be regarded as EXTRA for all copier

functions and no original size will be displayed.

Disabling of document feeder

This program is used to prevent use of the reversing

automatic document feeder when it malfunctions. In

this case, scanning can still be performed using the

document glass.

Disabling of duplex

This program is used to disable duplex printing when

the duplex module malfunctions. If this program is set,

only one-sided printing can be performed.

Disabling of large capacity cassette

Use this program when you wish to prohibit use of the

large capacity cassette or when it has failed.

Disabling of stapler

This program is used to disable stapling when the

stapler unit of the finisher or the saddle stitch finisher

malfunctions.

Disabling of punch

Use this program when you wish to prohibit punching

or when the punch unit of the finisher or saddle stitch

finisher has failed.

Disabling of finisher

Use this program when you wish to prohibit use of the

finisher or saddle stitch finisher, or when either has

failed.

Disabling of inserter

Use this program when you wish to prohibit use of the

inserter or when it has failed.

Disabling of covers/inserts mode

Use this program when you wish to prohibit use of the

covers/inserts mode.

GENERAL PROGRAMS