Crestron CLW-SLVD1 사용자 설명서 - 페이지 6

{카테고리_이름} Crestron CLW-SLVD1에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron CLW-SLVD1 13 페이지. Crestron clw-dim1 wall box dimmer: user guide

페이지 인쇄

CLW-DIM1, DIMS1, & SLVD1(W/A/B)

5. Push all power wires back into the wallbox and

fasten the devices to their respective wallboxes

with the provided screws.

6. Attach decorative faceplates.

7. Restore power at the circuit breaker.

Operation

The -DIM1, -DIMS1, and -SLVD1 have one large

pushbutton. The -DIM1 and -DIMS1 also have a three-

position mode selection switch. The function of the

pushbutton is determined by the position of the mode

selection switch. Refer to the following diagram.

NOTE: The -SLVD1 does not have a mode selection

switch. It emulates the operation of the -DIMS1 to which

it is connected unless the mode selection switch of the

master is set to "OFF".

Buttons of CLW-DIM1, -DIMS1, and -SLVD1

Button

Mode Selection Switch

(-DIM1 & -DIMS1 Only)

OFF

When the mode selection switch is in the "OFF" position,

the pushbutton will not have any function and the load is

disconnected from the power source. This must be used

when changing light bulbs to ensure that the load is fully

disconnected from power.

ADJ

When the mode selection switch is in the "ADJ" position,

the pushbutton is used to switch between the "Preset 1-

High" and "Preset 1-Low" presets (typically "On" and

"Off") as well as adjust the lighting level. Tap the

pushbutton to fade up or down to either of the two preset

lighting levels. Tap the pushbutton while the lighting

level is fading to jump directly to the preset lighting level

without fading. (i.e., tapping while the lighting level is

fading up will jump to the "Preset 1-High" level without

fading, tapping while the lighting level is fading down

will jump to the "Preset 1-Low" level without fading).

While the light is off, double-tap the pushbutton to jump

directly to the "Preset 1-High" lighting level without

fading.

The lighting level can be adjusted by pressing and holding

the pushbutton. After a ½ second, the lighting level will

6 • Stand Alone Wall Box Dimmer : CLW-DIM1, DIMS1, & SLVD1

ramp up or down. The lighting level will stop at

maximum brightness (100%) if the lighting level was

ramping up or minimum brightness (0%) if the lighting

level was ramping down. To continue ramping the

lighting level in the opposite direction, release the

pushbutton, then press and hold the pushbutton again.

When the desired lighting level is reached, release the

pushbutton.

If the lighting level is to be stored as a preset, move the

mode selection switch to the PRE position. Press and hold

the pushbutton until the LED flashes.

PRE

NOTE: Before storing a preset, the lighting must be

adjusted to the desired level while in the ADJ mode.

When the switch is in the PRE position, it is in the preset

mode and can be used to recall and/or store preset lighting

levels. The pushbutton is used to recall and/or store the

"Preset 1-High" and "Preset 1-Low" presets. Pressing and

releasing the pushbutton will fade to the preset lighting

level over a preset amount of time*. Tapping the

pushbutton while the light is fading will cause the light

level to "jump" directly to the preset without fading.

Pressing and holding the pushbutton until the LED flashes

will store the current lighting level.

The preset fade time can only be adjusted through Crestron

programming software.

To store preset values for "Preset 1-High" and "Preset 1-

Low"; while in the PRE mode, recall the lighting level to

be changed. Switch to the ADJ mode and adjust the

lighting to the desired level. Move the mode selection

switch to PRE. Press and hold the pushbutton until the

LED flashes to store the new preset value.

NOTE: If a new preset value for "Preset 1-High" is

lower than the stored value for "Preset 1-Low", the

previously stored value for "Preset 1-Low" becomes

"Preset 1-High". Similarly, if a new preset value for

"Preset 1-low" is higher than the value stored for "Preset

1-High", the previously stored value for "Preset 1-High"

becomes "Preset 1-Low".

NOTE: The default preset light values for each preset

are:

•

Preset 1-High: 100%

•

Preset 1-Low: 0%

NOTE: The device may be warm to the touch during

operation. This is normal.

Installation Guide – DOC. 6250A