Sharp Notevision XG-C430X 설정 매뉴얼 - 페이지 35

{카테고리_이름} Sharp Notevision XG-C430X에 대한 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Notevision XG-C430X 45 페이지. True xga portable lcd projectors
Sharp Notevision XG-C430X에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 사양 (2 페이지), 사양 (2 페이지)

페이지 인쇄
Sharp Notevision XG-C430X 설정 매뉴얼
Password Setting
([5]Password)
Carrying out security protection using password.
setup>5
Password
:
: sharppj
Please Enter
(change)
—>
sharppj
1 1 1 1 1 Enter "5" and press the "Enter" key.
2 2 2 2 2 Enter password and press the "Enter" key.
Display set password (*).
Note
• Password can be up to 8 characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
• In the default state, the password is not set.
RS-232C Baud Rate Set-
ting
([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
setup>6
0 ...
9600 bps
1 ... 38400 bps
2 ... 115200 bps
Baud Rate Select[0-2] :2
RS-232C Baud Rate : 115200 bps
1 1 1 1 1 Enter "6" and press the "Enter" key.
2 2 2 2 2 Select and enter the number 0, 1 or 2 and
press the "Enter" key.
Display set baud rate (*).
Note
• Set the projector's baud rate to the same rate as
that used by the computer.
Setting up the Projector Using RS-232C or Telnet
Projector Name Setting
([7]Projector Name)
It is possible to assign a projector name.
1
setup>7
Projector Name
2
Please Enter
(change)
*
1 1 1 1 1 Enter "7" and press the "Enter" key.
2 2 2 2 2 Enter projector name.
Display set projector name (*).
• Projector name can be up to 12 characters.
• You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When "a-z" are input, they are converted to "A-Z"
automatically.)
• It is the same as the name which can be con-
firmed or set, using RS-232C commands "PJN0",
"PJN1", "PJN2" and "PJN3".
DHCP Client Setting
([8]DHCP Client)
1
Setting DHCP Client to "Enable" or "Disable".
Example: When setting DHCP Client to "Enable"
2
*
setup>8
note: It sets DHCP Client.
0 ... Disable
1 ... Enable
DHCP Select[0-1] : 1
DHCP Client : Enabled
Success get data from DHCP server.
[MAC Address
[IP Address
[Subnet Mask
[Default Gateway ] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1 1 1 1 1 Enter "8" and press the "Enter" key.
2 2 2 2 2 Enter "1" and press the "Enter" key.
Display the obtained values (*).
: XX-XXXX
: MY XX-XXXX
—>
MY XX-XXXX
Note
] : [08:00:1F:B1:B7:74]
] : [192.168.150.2]
] : [255.255.255.0]
1
2
*
1
2
*
-35