Bittel 38-10S 사용자 설명서 - 페이지 2

{카테고리_이름} Bittel 38-10S에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bittel 38-10S 4 페이지. 38 series

페이지 인쇄

2. Installation

The Uranus Series is designed for hotel applications and behind

a registered PBX system in hotel. Determine you have the

correct modular jack for connecting the telephone. If you do not

have a modular jack, one may be obtained at minimal cost at a

local hardware store, discount store or home center.

1) Located on the left side of the Uranus phone is a modular jack.

Insert one end of the coiled handset cord into this jack (you will

hear the coil cord click when properly inserted.)

2) Insert the other end of the coiled handset cord into the modular

jack on the handset.

3) Turn the telephone so the back panel is facing you. Insert either

end of the line cord into the jack on the back of the telephone

labeled " " " " TO TEL

TO TEL

TO TEL" " " " .

4) Insert the other end of the line cord into a telephone wall jack.

Once your telephone is connected, place the paper faceplate

over the keys. The plastic overlay slips into place by hooking the

tabs on the overlay into the recessed slots located on both sides.

The overlay is easiest to insert when the left or right side tabs

are inserted first, and the middle of the overlay is slightly bowed

to allow for insertion of the other tabs.

Controls, , , , Connections and Function keys

Controls

Connections and Function keys

Controls

Connections and Function keys

(1) Handset Wall Mount Clip

(1) Handset Wall Mount Clip – Clip to hold handset on

(2) Hook Switch.

(3) Insert hole for placard.

(4) Data Port

– Provides access to the telephone line for

(4) Data Port

connection of modem, fax, or answering

machine.

(5)Tel. Jack

– Modular jack to connect telephone line

cord.

(6) Data Switch

(6) Data Switch –Adjust the data in Line 1 or Line2.

(6) Data Switch

(7)Ring Volume

(7)Ring Volume – Adjusts ringer volume to LOW or HI.

(7)Ring Volume

(8)/(9) Plastic and paper faceplate.

(10) Memory Keys

(10) Memory Keys – Programmable to add special features

or one touch dial frequently dialed numbers.

(11) Dial Keys

– Oversized keypad for ease of dialing.

(12) [Pause] key

-- Hidden key inserts a 3.6 second pause

(12) [Pause] key

in stored numbers

(13) SPKR Key – Activates speakerphone function

(13) SPKR Key

(14) Redial Key

– Redials the last number dialed.

(15) MIC. of Speaker ( For Speaker phone).

(16) Flash Key

Enters a 600ms hook switch flash for

accessing special telephone system

features.

(17) Message Waiting Light

(17) Message Waiting Light – Indicates the phone is ringing

(17) Message Waiting Light

Responds to Neon/90V message waiting signal.

(18) Store Key

–

Hidden key for storing numbers to

Memory.

(19) Hold Key

– Places a calling on hold.

(20) VOL key – Key steps through the three available

(20) VOL key

handset /speaker volume levels [Normal –

Medium – High – Normal]

hook in wall mount

application

or a message is waiting.

3.Operation

3.1 PLACING A CALL

Using the Handset

1) Lift the handset.

2) Listen for dial tone. Dial the desired number, or

press [REDIAL] key to automatically dial a number.

3) To end the call, hang up by replacing the handset.

Using the Speakerphone

1) Press the [SPKR] key

2) Wait for a dial tone.

3) Dial a phone number.

4) Press [SPKR] key when finished.

3.2 RECEIVING A CALL

Using the Handset

When the phone rings, the [MWL] flashes rapidly.

1)Pick up the handset.

2)To end the call, hang up by replacing the handset.

Using the speaker phone

When the phone rings, the [MWL] flashes rapidly.

1)Press the [SPKR] key.

2)The speakerphone comes on automatically.

3)Press [SPKR] when finished.

---- Page 2----

ABC

DEF

GHI

JKL

MNO

WXYZ

PQRS

TUV

VOL

PAUSE

STORE

HOLD

FLASH

REDIAL

1918

MUTE

SPKR