Siemens SIMATIC ET 200SP 매뉴얼 - 페이지 14

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 30 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (44 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 매뉴얼
Product overview
2.4 Properties of the interfaces
RS232 signals
The table below shows the meaning of the individual RS232 accompanying signals.
Table 2- 1
Signals of the RS232 interface
Signal
Designation
TXD
Transmit Data
RXD
Receive Data
RTS
Request To Send
CTS
Clear To Send
DTR
Data Terminal Ready
DSR
Data Set Ready
RI
Ring Indicator
DCD
Data Carrier Detect
14
Meaning
Transmit data; transmit cable logically held to "1" by communication module in idle
state.
Receive data; receive cable logically held to "1" by communication partner in idle state.
Request to send
RTS set to "ON": Communication module ready to send; signals to the communication
partner that there is data ready to send
RTS set to "OFF": Communication module does not send
Clear to send
CTS set to "ON": Signals "clear to send" to the communication partner
CTS set to "OFF": Signals "Not clear to send" to the communication partner
DTR set to "ON": Communications module switched on, ready for operation
DTR set to "OFF": Communications module not switched on, not ready for operation
DSR set to "ON": Communication partner signals "ready for operation"
DSR set to "OFF": Communication partner not switched on, not ready for operation
Incoming call when connecting a modem
Carrier signal when connecting a modem. The communication partner signals with a
high level that it detects incoming data on the cable.
CM PtP communication module (6ES7137-6AA00-0BA0)
Manual, 01/2013, A5E03790792-01