Siemens SIMATIC ET 200SP 매뉴얼 - 페이지 19

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 25 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (44 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 매뉴얼
5.3

Diagnostics alarms

A diagnostics alarm is output for each diagnostics event and the DIAG LED on the
module flashes. The diagnostics alarms can, for example, be read from the diagnostics
buffer of the CPU. You can evaluate the error codes with the user program.
Table 5- 4
Diagnostics alarms, their meaning and how to deal with them
Diagnostics alarm
Error code
Channel temporarily
1F
unavailable
Short-circuit
1
Wire break
6
Parameter
10
assignment error
No load voltage
11
DI 8x24VDC ST digital input module (6ES7131-6BF00-0BA0)
Manual, 07/2014, A5E03574157-AC
Meaning
Firmware update in progress or update
H
has been cancelled.
The module reads no process values in
this state.
Short-circuit to ground at encoder supply
H
Impedance of encoder circuit too high.
H
Wire break between the module and
sensor
Channel not connected (open)
The module cannot evaluate
H
parameters for the channel.
Incorrect parameter assignment.
No or insufficient supply voltage L+
H
Interrupts/diagnostics alarms
5.3 Diagnostics alarms
Remedy
Wait for firmware update
Restart the firmware update
Correct the process wiring
Use a different encoder type or modify
the wiring, for example, using cables with
larger cross-section
Connect the cable
Disable diagnostics
Connect a resistor of 25 kilohms to
45 kilohms to the encoder contacts
Correct the parameter assignment
Check supply voltage L+
on the BaseUnit
Check BaseUnit type
19