Siemens SIMATIC ET 200SP 매뉴얼 - 페이지 14

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 35 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (44 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 매뉴얼

3 Mode of Operation

Mode of Operation
3
3.1

General overview

Figure 3-1
1
2
LIOLink_RF200_
SwitchAntenna
Watchdog timer
3
Transponder
detected
4
LIOLink_RF200_
ReadTag/WriteTag
Done
5
LIOLink_RF200_
SwitchAntenna
The table below shows the individual steps of the read/write function
(reading/writing RFID data from/to the transponder).
Table 3-1
No.
1.
2.
3.
4.
5.
Read/write data with IO-Link
Entry ID: 73565887,
V3.4,
Start
Error
No transponder
detected
5 s
Error
Use the "READ"/"WRITE" button on the user interface of the SIMATIC Panel
(HMI) to start the read/write function. The two functions can also be started via a
watch table.
The " LIOLink_RF200_SwitchAntenna" library block switches on the antenna
field at the reader.
The "TONR" watchdog timer monitors whether a transponder is located in the
detection/write area within the monitoring time of 5 s.
If a transponder is detected in the reader's field within the 5 seconds, the "
LIOLink_RF200_ReadTag" / "LIOLink_RF200_WriteTag" library block will
read/write the RFID data from/to the transponder.
The " LIOLink_RF200_SwitchAntenna" library block switches off the antenna
field at the reader when:
the read/write job has been successfully completed
an error has occurred while processing the read/write job
no transponder was detected in the reader's field within the specified time.
Turning off the antenna field terminates the read/write function.
06/2022
Error and
status output
Description
14