Siemens SIMATIC ET 200SP 장비 매뉴얼 - 페이지 22

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 장비 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 32 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (44 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 장비 매뉴얼
5.2

Interrupts

The digital output module RQ 4×120VDC-230VAC/5A NO MA ST supports diagnostics
interrupts.
Diagnostics interrupts
The module generates a diagnostic interrupt at the following events:
• Parameter assignment error
• Supply voltage missing
• Channel temporarily unavailable
5.3

Diagnostics alarms

A diagnostics alarm is generated and the DIAG-LED flashes on the module for each
diagnostics event. You can read out the diagnostics alarms, for example, in the diagnostics
buffer of the CPU. You can evaluate the error codes with the user program.
Table 5- 5
Diagnostics alarms, their meaning and corrective measures
Diagnostics alarm
Error code
Parameter assign-
10
ment error
Supply voltage miss-
11
ing
Channel temporarily
1F
unavailable
Digital output module RQ 4x120VDC-230VAC/5A NO MA ST (6ES7132-6MD00-0BB1)
Equipment Manual, , A5E36107692-AB
Meaning
The module cannot evaluate parameters
H
for the channel.
Incorrect parameter assignment.
Missing or insufficient supply voltage L+
H
Firmware update is currently in progress or
H
has been canceled.
The module does not output any process or
substitute values in this state.
Interrupts/diagnostics alarms
5.2 Interrupts
Solution
Correct the parameter assignment
Check supply voltage L+ on the
BaseUnit
Check BaseUnit type
Wait for firmware update
Restart the firmware update
21