Siemens SIMATIC ET 200SP 매뉴얼 - 페이지 18

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 50 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (44 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 매뉴얼
2.2

Functions

Introduction
The interface module supports the following PROFINET IO functions:
• Supported Ethernet services: ICMP, ARP, SNMP, LLDP
• Port diagnostics
• Disabling of ports
• Minimum update time 1 ms
• Device replacement without programming device (PG) and without topological
configuration
• Media redundancy protocol (MRP)
• Distribution of module channels to a maximum of 4 submodules
• Real-time communication
• Use of fail-safe modules
• System redundancy R1
• Value status of I/O modules
• Reading out service data
• Reference temperature distribution
• H-Sync forwarding
• Setting the time
• Time distribution
• Diagnostic interrupts
• Hardware interrupts
• Removal/insertion of multiple I/O modules during operation (Multi Hot Swap)
• Maintenance events
• Reset to factory settings via PROFINET IO
• Firmware update via PROFINET IO
• Identification data I&M 0 to I&M 3
You can find more information on the system functions in the ET 200SP Distributed I/O
System system manual (https://support.industry.siemens.com/cs/ww/en/view/58649293).
Note
Redundant firmware update
You can only perform a redundant firmware update via MFCT.
Interface Module IM 155-6 PN R1 (6ES7155-6AU00-0HM0)
Equipment Manual, 11/2022, A5E51160307-AA
Product overview
2.2 Functions
17