Siemens Simatic S7-1500 매뉴얼 - 페이지 18

{카테고리_이름} Siemens Simatic S7-1500에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens Simatic S7-1500 25 페이지. Digital output module dq 16x230vac/2a st relais (6es7522-5hh00-0ab0)
Siemens Simatic S7-1500에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 매뉴얼 (37 페이지), 매뉴얼 (47 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 사용자 설명서 (45 페이지), 매뉴얼 (27 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (47 페이지), 매뉴얼 (43 페이지), 매뉴얼 (48 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (50 페이지), 매뉴얼 (34 페이지), 사용자 설명서 (44 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (41 페이지), 매뉴얼 (50 페이지), 매뉴얼 (40 페이지), 안전 프로그래밍 매뉴얼 (48 페이지), 통신 사용 설명서 (36 페이지), 매뉴얼 (40 페이지), 매뉴얼 (42 페이지), 애플리케이션 설명 (50 페이지), 매뉴얼 (28 페이지), 매뉴얼 (33 페이지), 매뉴얼 (49 페이지), 매뉴얼 (36 페이지), 매뉴얼 (41 페이지), 매뉴얼 (46 페이지), 매뉴얼 (38 페이지), 매뉴얼 (35 페이지), 매뉴얼 (39 페이지), 매뉴얼 (28 페이지), 매뉴얼 (35 페이지), 장비 매뉴얼 (35 페이지), 매뉴얼 (50 페이지), 장비 매뉴얼 (32 페이지), 장비 매뉴얼 (38 페이지), 매뉴얼 (29 페이지), 장비 매뉴얼 (38 페이지), 매뉴얼 (34 페이지), 매뉴얼 (36 페이지), 장비 매뉴얼 (50 페이지), 매뉴얼 (45 페이지)

Siemens Simatic S7-1500 매뉴얼
Interrupts, diagnostic alarms, error and status alarms

5.2 Diagnostic alarms

5.2
Diagnostic alarms
Diagnostic alarms
The following table shows the meaning of the diagnostic alarms and possible remedial
measures for the respective cause.
One of the following "LED images" indicates directly on the PS that a diagnostic alarm was
triggered.
● The red ERROR-LED is flashing.
Indicates external or internal errors.
● The yellow MAINT-LED is lit.
Maintenance; a maintenance request is active.
● All three LEDs are flashing permanently
The PS is in "Defective" state.
In STEP 7, the diagnostic results are displayed in plain text by means of the online and
diagnostic view. You can read the diagnostic data records by means of the "RDREC"
instruction.
Table 5- 2
Diagnostic alarms, their meaning and remedies
Diagnostic alarm
Error
code
Dec.
External error
Supply
266
voltage missing
Internal error
Overtemperature
5
D
Overvoltage back-
267
plane bus
Safety shutdown
285
Maintenance
Switch turned off
268
Malfunction
Module failure
256
18
Meaning
Hex.
010A
No supply voltage, or incorrect
D
H
insertion of the power connector
into the PS.
0005
Overtemperature on the printed
H
circuit board.
010B
High EMC interference or a defec-
D
H
tive PS, CPU or IM inserted.
011D
Reliable operation of the module
D
H
is no longer guaranteed.
010C
The PS is switched off.
D
H
0100
PS failure.
D
H
Reac-
tion
1
2
2
2
1
3
Power supply module PS 60W 24/48/60VDC HF (6ES7505-0RB00-0AB0)
Remedial measures
Check the supply voltage.
Check PS load. Isolate PS from
mains. Wait one minute before you
power on the PS again.
Eliminate electromagnetic interfer-
ence. Check inserted modules and
bus connectors. Isolate PS from
mains. Wait one minute before you
power on the PS again.
Check ambient conditions. Isolate PS
from mains. Wait one minute before
you power on the PS again.
Switch on PS.
Replace PS.
Manual, 01/2019, A5E39450002-AB