Epson 1715C - PowerLite XGA LCD Projector 운영 매뉴얼 - 페이지 31

{카테고리_이름} Epson 1715C - PowerLite XGA LCD Projector에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 1715C - PowerLite XGA LCD Projector 36 페이지. Remote control information
Epson 1715C - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 빠른 설정 (4 페이지), 운영 매뉴얼 (47 페이지), 설치 매뉴얼 (19 페이지), 사용자 설명서 (1 페이지), 부품 목록 (1 페이지), 문서 업데이트 (12 페이지), 기능 설명서 (5 페이지), 소프트웨어 설명서 (2 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지), 사양 (2 페이지), 설치 핸드북 (8 페이지)

페이지 인쇄
Epson 1715C - PowerLite XGA LCD Projector 운영 매뉴얼

Setting the mail notification function

The mail notification function can be used to send corresponding notification
messages to a preset e-mail address when a projector that is connected to the
network assumes a certain status, or if it experiences a problem or warning. By
using this function, the operator can be notified of a projector's status or
problems even when the operator is in a different location from the projectors.
TIP
• Up to three addressees (destinations) can be registered and
messages can be sent to all of them at once.
• If a critical problem develops with a projector which causes it to
suddenly stop working, it may not be possible for the projector to
send a message notifying an operator of the problem.
• If "Standby Mode" is set to "Network ON" or "Network
Monitoring" is set to "ON" in the projector configuration menus,
you can monitor the projector even when it is in standby mode
(when its power is turned off). See your User's Guide for more
information.
• On some projectors, the mail notification function can be set in the
configuration menu. When notification messages are set to be sent
in the projector's configuration menu, both the settings in the
configuration menu and settings made on EMP Monitor are
functional.
• Detectable status with the mail notification function differs with the
projector you are using.
PROCEDURE
Select "Mail notification function" from the "Tool"
1
menu.
The "Set mail notification function" window will be
2
displayed.
Set the following parameters.
Mail notification
Set to "ON" to use the mail notification function.
function
SMTP server
Enter the IP address of the SMTP server.
IP address
Up to a maximum of 255 bytes can be entered.
When you change a port number of the SMTP
server, specify this port number. The default value
is "25".
You can enter a valid number from 1 to 65535.
Sender mail
Enter the sender's e-mail address. Up to a
address
maximum of 255 bytes can be entered.
Recipient
mail address 1
Specify the destination addresses for the
Recipient
notification e-mail. Up to three destinations can be
mail address 2
set. Up to a maximum of 255 bytes can be entered.
Recipient
mail address 3
30