Samsung 460PXN - SyncMaster - 46" LCD Flat Panel Display 사양 - 페이지 8
{카테고리_이름} Samsung 460PXN - SyncMaster - 46" LCD Flat Panel Display에 대한 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. Samsung 460PXN - SyncMaster - 46" LCD Flat Panel Display 10 페이지. Quick guide (korean)
Samsung 460PXN - SyncMaster - 46" LCD Flat Panel Display에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (42 페이지), 빠른 시작 매뉴얼 (41 페이지), (한국어) 빠른 시작 매뉴얼 (39 페이지)
페이지 인쇄
Accessories
Stand
631.6
222.8
STN-L320PB (320PX)
974.0
295.0
STN-L403TB (460PX/460PXn)
Speaker
49.5
100.0
78.0
124.1
SP-L320PB/S (320PX)
104.0
136.6
80.0
SP-L400PB/S (400PX/400PXn)
104.0
136.6
80.0
SP-L460PB/S (460PX/460PXn)
974.0
295.0
STN-323TB (400PX/400PXn/400TXn)
Ceiling Mount
CML 500D
( 400 PX/ 400 PXn/ 400 TXn/ 460 PX/ 460 PXn)
Wall Mount
22.2
18.0˚
50.3
WMB- 4050 PS (400PX/400PXn/460PX/460PXn)
Vertical Mount
21.4
14.5˚
47.9
VMN 4240 D (400PX/400PXn/460PX/460PXn)
Components (WMB-4050PS)
ASSY -HINGE (LEFT): 1 EA
ASSY -HINGE (RIGHT): 1 EA
WALL BRKT-PLATE: 1 EA
Only use the components and accessories shipped with the product.
Wall Bracket Assembly & Wall Bracket & Wall Bracket Angle Adjustment (WMB- 4050 PS)
Check the installation diagram and mark the drill points
Remove the 4 screws on the back of the product.
on the wall. Use the 5.0 mm bit to drill holes deeper than
Insert screw B into the plastic hanger.
35 mm. Fix each anchor in the corresponding hole.
Match each of the brackets and hinge holes to the cor-
responding anchor holes and insert and tighten the 11 A
screws.
• Contact a technician for installing the wall bracket.
• Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.
• This product is intended for installation on cement walls. The product may not be secure when installed on plaster or wood walls.
Samsung LCD Display | 14 + 15
Samsung Plasma Display | 3 + 15
236.0
699.2
85.0
85.0
35.0
2-99.2
2-55.2
100.0
100.0
240.0
WML 4001 D (320PX)
499.2
230.0
2-99.2
85.0
85.0
2-55.2
234.0
45.0
45.0
282.0
330.0
WML 4001 D (320PX)
PLASTIC: 4 EA
SCREW: 11 EA
SCREW: 4 EA
SCREW: 11 EA
1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it
forward (direction of the arrow) to adjust the angle.
(See the figure to the right)
3. You can adjust the bracket angle between -2˚ and 15˚.
27.5