DIGITAL FORECAST X-MC 사용자 설명서 - 페이지 2

{카테고리_이름} DIGITAL FORECAST X-MC에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DIGITAL FORECAST X-MC 2 페이지. Multi converter

페이지 인쇄

User Manual

Troubleshooting

When the screen is cracked or HDMI input noise is generated.

► A low-priced (or uncertified) HDMI cable may cause a data loss at more than 1080i resolution.

The verification method is to check the video quality of more than 1080i resolution on the monitor in direct

connection between a problematic HDMI cable and video display unit NOT as via X_MC.

If the HDMI cable is the cause, the display keeps showing the same symptom.

Therefore, Genuine HDMI cable is recommended.

When Analog audio is off.

► Please check the condition of Audio at Video Output of the SDI or HDMI which contains Audio

data. If the checked Audio is normal, it may be a temporary symptom by ESD(Electrostatic

Discharge)

In this case, please reboot the product as turning OFF and ON the product : forced RESET

User Manual

3. The OSD key enables the user to select the following mode.

Optional : YUV422, RGB444

※ Notes

This feature can be used only available for VGA output

In case of selecting RGB444 mode for SDI, CVBS, and COMPONENT, the output mode will be abnormally

displayed, because those support YUV422 mode only.

Display Test Pattern

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 6. Test Pattern.

2. When "Test Pattern" menu is selected, the following menu will be displayed.

3. The OSD key enables the user to select whether to output.

Selectable : On, Off

The output screen display the Color bar, and the -20dB of Tone signal is contained in Audio 1 group consisting

of 2ch.

Bridge X_MC

How to use OSD Menu

The OSD key (switch) is located on the top left of the product.

Selecting the input port

1. Press the OSD key and hold on for a while. Then OSD menu will appear like below.

2. When selecting ""Video In SEL", the following sub-menu is displayed.

3. The OSD key enables the user to select a needed Video Input type.

Optional : COMPONENT, HDMI, SDI, COMPOSITE, VGA

When the selection is made, the relevant Input LED is ON.

※ Notes

To use the COMPONENT, VGA, the input port must be equipped with an additional gender.

Bridge X_MC

Aspect Ratio Converter

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 7. ARC Mode.

2. When "ARC Mode" menu is selected, the following menu will be displayed.

3. The OSD key enables the user to select whether to output.

Selectable : Bypass, 4:3, 16:9

Adjusting the Screen

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 8. Picture.

User Manual

4. "Audio In SEL" menu shows the selectable Audio inputs.

When "AUTO" is selected, the Audio input of the related Video is selected.

In other words, the video of SDI, HDMI contains Audio data.

If the other types of video input are selected, Analog Audio input is selected accordingly.

Optional : AUTO, Analog, AES / EBU

Selecting the resolution

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 3. Out Format.

2. When "Out Format" menu is selected, the following menu will be displayed.

3. A needed resolution can be selected by using OSD key.

4. "By pass" mode provides the same resolution of the input, excluding the PC resolution.

"Fixed 1080i" is fixed as the output resolution of 1080i (1080i50 or 1080i59, will be displayed depending on the

frequency)

Selectable Resolutions :

Bypass, 480i_NTSC, 576i_PAL, 720p50, 720p59, 720p60, 1080i50, 1080i59, 1080i60, 1080p24, 1080p25,

1080p30, 1080p50, 1080p59, 1080p60, 640x480p60, 800x600p60, 1024x768p60, 1280x1024p60,

1360x768p60, 1600x1200p60, 1440x900p60, Fixed 1080i

User Manual

2. When " Brightness " menu is selected, the following menu will be displayed.

3. The OSD key enables the user to select the following values of "Brightness"output

The OSD key operation enables the user to change its value

The remaining "Contrast" and "Saturation" can be adjusted in the same way.

SAVE

1. Press the OSD key and hold on for a while in order to show the initial display menu

And move to 9. Save

2. When "Save" menu is selected, the following menu will be displayed.

3. The OSD key enables the user to select whether to save the changed configuration.

Choices: Yes, No

※ In spite of not saving through "SAVE" menu,

the changed setting is automatically saved when OSD menu disappears.

Bridge X_MC

Magnifying the Screen

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 4. Zoom.

2. When "Zoom" menu is selected, the following menu will be displayed.

3. The OSD key enables the user to select the following values

Selectable : No Zoom, 5%, 10%, 15%, 20%, 25%, 30%, 35%

Selecting the output Color

1. Press the OSD key and hold on for a while in order to show the initial display menu.

And move to 5. Color Mode.

2. When "Color Mode" menu is selected, the following menu will be displayed.

Bridge X_MC

Initialize

1. Press the OSD key and hold on for a while in order to show the initial display menu. And move to 10. Factory

Set.

2. When "Factory Set" menu is selected, the following menu will be displayed.

3. The OSD key to select whether to initialize the entire setting.

Choices: Yes, No