Epson 755c - PowerLite XGA LCD Projector 부품 설명서 - 페이지 4

{카테고리_이름} Epson 755c - PowerLite XGA LCD Projector에 대한 부품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 755c - PowerLite XGA LCD Projector 26 페이지. Release of check tool for network projectors v1.00 for windows
Epson 755c - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사양 시트 (2 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 사용자 교체 가능 항목 (1 페이지), 빠른 설정 (2 페이지), 설치 매뉴얼 (19 페이지), 사용자 설명서 (1 페이지), 기능 설명서 (5 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Epson 755c - PowerLite XGA LCD Projector 부품 설명서
Epson PowerLite 755c/765c Projector
3. Press the P
button on top of the projector or on the
Power
remote control.
Projector
The projector beeps once and the
as the projector warms up, then an image begins to appear.
When the
light stops flashing and remains green, the
Power
projector is ready for use.
Warning:
Never look into the lens when the lamp is on. This can damage
your eyes, and is especially dangerous for children.
If you've connected a Windows
projector, you may see a New Hardware Wizard saying
your computer has found a plug-and-play monitor; if so,
click
.
Cancel
If you don't see the image you want, press the
button on the projector or the
Search
the remote control until you see the image you want to
project.
If you are prompted to enter a password, see "Starting the
Projector with a Password" on page 10.
Note:
You can also use the Source buttons on the remote control to
switch between devices connected to the ports identified on each
button. For details, see page 5.
If a projected image fails to appear, see "You Can't Project an
Image" in the next column.
When you're done with your presentation, shut down the
projector as described on page 7. Shutting down the projector
correctly prevents premature lamp failure and possible damage
from overheating.
4
Epson PowerLite 755c/765c Projector
-
Power button
Remote control
light flashes green
Power
®
-based computer to the
Source
button on
Search

You Can't Project an Image

If you don't see the image you are trying to project, try the
following:
Make sure the cables are connected correctly.
Make sure the
Power
lens cap is off.
If you've connected more than one computer and/or video
source, you may need to press the
the projector's control panel or
remote control to select the correct source. (Allow a few
seconds for the projector to sync up after pressing the
button.)
If you're using a PC notebook, see below.
The Projector and Notebook Don't
Display the Same Image
If you're projecting from a notebook, and you can't see your
image on the projection screen and on your computer at the
same time, follow these guidelines.
If you're using a PC notebook:
On most systems, there's a function key that lets you toggle
between the LCD screen and the projector, or display on
both at the same time. It may be labeled
an icon such as
key while pressing it. Allow a few seconds for the projector to
sync up after changing the setting.
If the function key doesn't permit you to display
simultaneously on both screens, you should check your
monitor settings to make sure both the LCD screen and the
external monitor port are enabled.
From the Control Panel, open the
Display Properties dialog box, click the
click
. The method for adjusting the settings
Advanced
varies by brand; you may need to click a
make sure the external Monitor port is set as your primary
display and/or enabled. See your computer's documentation
or online help for details.
8/05
light is green and not flashing and the
Source Search
button on the
Search
CRT/LCD
. You may have to hold down the
utility. In the
Display
Settings
Monitor
button on
or have
Fn
tab, then
tab, then