Epson 7850p - PowerLite XGA LCD Projector 빠른 설정

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 빠른 설정을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 2 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 브로셔 및 사양 (2 페이지), 제품 정보 매뉴얼 (25 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Epson 7850p - PowerLite XGA LCD Projector 빠른 설정
EPSON
1
Turn On Your Equipment
1
Connect the power cord to the back of
the projector and plug the other end
into a grounded outlet.
2
Remove the lens cover.
3
Remove the battery cover on the remote
control. Locate the batteries that came
with the projector and insert them as
shown. Then replace the battery cover.
4
Push up on the remote control's ON/OFF
switch to turn it on.
5
Aim the remote control at the projector and press the red
button. The projector's
power light flashes green and then stays on.
CAUTION: Before unplugging the projector...
To shut the projector down properly:
1. Press the
Power button twice. Let the projector cool while the
power light flashes orange (about 30 seconds).
2. Once the light stops flashing and stays on, it's safe to unplug
the projector.
Never unplug the projector when the
flashing orange.
2

Adjust the Image

1
To raise the image, press the blue foot release button for the front
adjustable foot and lift the front. Release the button to lock the
foot in position.
PowerLite
7850p
®
®
Quick Setup
ON/OFF
switch
Power
power light is green or
2
Rotate the focus ring to sharpen the image.
Rotate the zoom ring to reduce or enlarge the image.
Focus ring
Zoom ring
3
If your image looks like
or
to one side of the screen at an angle. Place it directly in front of the
screen, facing the screen squarely.
4
If your image looks like
or
on the projector.
3
Choose a
Presentation Method
How do you want to get images to the projector?
To connect to a laptop, see "If connecting
to a laptop" below.
To project over an 802.11b network, see
"If projecting wirelessly" on the back of this sheet.
You must have installed the projector's EasyMP
software and configured your projector and
computer before you can project wirelessly.
See your User's Guide for instructions.
To give a presentation stored on a memory card,
see Chapter 5 in your User's Guide.
If connecting to a laptop...
1
Make sure you've turned on the projector and adjusted the image
as described in sections 1 and 2.
2
Locate the VGA cable that came with the projector. Connect one
end to the projector's Computer port.
Connect the other end to your laptop's video-out port or
monitor port. If you can't connect the cable to your PowerBook
you may need to use an adapter. See your User's Guide for
instructions.
3
Press the Comp button on the remote control until your
computer image is displayed.
, you've placed the projector off
, press the
or
Sync buttons
TM
®
,
Turn over