Epson 821p - PowerLite XGA LCD Projector 빠른 설정

{카테고리_이름} Epson 821p - PowerLite XGA LCD Projector에 대한 빠른 설정을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 821p - PowerLite XGA LCD Projector 2 페이지. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Epson 821p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 사양 (2 페이지), 운영 매뉴얼 (47 페이지), 부품 목록 (1 페이지), 제품 정보 (15 페이지), 사용자 설명서 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (8 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 821p - PowerLite XGA LCD Projector 빠른 설정
C
onnect the projector
to your notebook
1
Locate the required cables:
Power cord
Computer cable
2
Connect the computer cable to the
Computer 1/Component Video 1
port on the projector.
3
Connect the other end to your notebook's video-out
or
monitor port.
NOTE:
If your notebook has a DVI connector, you need to either
connect a DVI-to-VGA adapter to the included computer cable (see
your computer's documentation), or purchase an optional DVI to
VGA cable (for a higher-quality image). See your User's Guide.
4
Connect the power cord to the
projector, then plug the other end
into a grounded electrical outlet.
T
urn on your equipment
1
Turn on your notebook.
2
Remove the projector's lens cap.
3
Make sure the
Power light
is orange and not flashing.
Power light is orange
4
Press the
Power button
to turn on the projector.
The projector beeps and
the
Power light flashes
as the projector warms up.
CAUTION: Before unplugging the projector...
Shut down the projector properly:
1. Press the
Power button twice. The lamp turns off, the
light flashes orange (about 20 seconds), and the projector beeps
twice to signal power is off.
2. Once the projector beeps, it's safe to unplug it.
Never unplug the projector when the
flashing orange.
and not flashing
Power button
Power
Power light is green or
Epson

Quick Setup

Follow these instructions to connect the projector to your
notebook. For other setup options, see your User's Guide.
A
djust the image
1
If you've turned on your notebook and you don't see an image, press
the Source Search button on the projector repeatedly until you see
your image.
NOTE:
If you still see a blank screen or have other display problems,
see the troubleshooting tips on the back of this sheet.
2
Rotate the focus ring to sharpen the image.
Focus ring
to sharpen
the image
3
Rotate the zoom ring to reduce or enlarge the image. (You can also
move the projector closer to or farther from the screen.)
4
If your image looks like
or
one side of the screen at an angle. Place it directly in front of the
center of the screen, facing the screen squarely.
5
If your image looks like
or
square up the image.
PowerLite
821p
®
®
Zoom ring
to adjust the
image size
, you've placed the projector off to
, use the
or
buttons to