Samsung UD55E-B 빠른 설정 매뉴얼
{카테고리_이름} Samsung UD55E-B에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Samsung UD55E-B 2 페이지.
Samsung UD55E-B에 대해서도 마찬가지입니다: 빠른 설정 매뉴얼 (2 페이지)
페이지 인쇄
Quick Setup Guide
UD46E-A UD46E-C UD46E-B
UD55E-B
The colour and the appearance may differ depending on the product, and the specifications are
subject to change without prior notice to improve the performance.
Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Checking the Components
- Contact the vendor where you purchased the product if any components
are missing.
- The pictures may look different from the actual components.
Warranty card
Quick Setup Guide
(Not available in some
Regulatory guide
locations)
Batteries
MagicInfo Software
Power cord
(Not available in some
DVD
locations)
Remote Control
DP cable
RS232C(IN) adapter
Holder-Ring (4EA) /
AUDIO adapter
Screw (4EA)
BN68-07319J-02
External sensor KIT
1
2
3
4
5
1
Aim the remote control towards this spot on the LCD Display.
- Keep the area between the remote sensor and remote control
obstacle-free.
Automatically detects the intensity of ambient light around a
2
selected display and adjusts the screen brightness.
3
The power indicator will turn off when the product is turned on.
It will blink in power-saving mode.
Use this button for turning the LCD Display on and off.
4
5
Switches from PC mode to Video mode.
Selects the input source that an external device is connected to.
Reverse Side
1
2
3
4
5
6
7
8
9
0
!
@
Troubleshooting Guide
Issues
Solutions
The screen keeps
Check the cable connection between the product
switching on and off.
and PC, and ensure the connection is secure.
No Signal is displayed
Check that the product is connected correctly
on the screen.
with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is
This message is displayed when a signal
displayed.
from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
Check the cable connection to the product.
screen look distorted.
The screen is not clear.
Adjust Coarse and Fine.
The screen is blurry.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears
Check that the resolution and frequency of the
unstable and shaky.
PC and graphics card are set within a range
There are shadows or
compatible with the product. Then, change the
ghost images left on the
screen settings if required by referring to the
screen.
Additional Information on the product menu
and the Standard Signal Mode Table.
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
Receives the remote control signal via the external sensor board
1
and outputs the signal via LOOP OUT.
Supplies power to the external sensor board or receives the light
2
sensor signal.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
3
MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI cable.
Connects to a source device using an HDMI cable.
4
5
Connects to a PC using a DP cable.
Connects to a source device using a D-SUB cable.
6
Connects to another product using a DP cable.
7
Receives sound from a PC via an audio cable.
8
Connects to the audio of a source device.
9
0
Connects to MDC using an RS232C adapter.
Connect to a USB memory device. (Only for update purpose)
!
Connects to MDC using a LAN cable.
@
Issues
Solutions
White does not really
Go to Picture and adjust the White Balance
look white.
settings.
The product will turn off
Go to System and make sure Sleep Timer is
automatically.
set to Off.
If a PC is connected to the product, check the
power status of the PC.
Make sure the power cable is connected
properly to the product and power outlet.
If the signal from a connected device is not
detected, the product automatically turns off
after 10 to 15 minutes.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does
Make sure that the batteries are correctly in
not work.
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.