Siemens dishwasher 사용 설명서 - 페이지 22

{카테고리_이름} Siemens dishwasher에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens dishwasher 30 페이지. Dishwasher
Siemens dishwasher에 대해서도 마찬가지입니다: 사용 설명서 지침 (29 페이지), 사용 설명서 (30 페이지), 사용 설명서 (30 페이지), 사용 설명서 (28 페이지), 사용 설명서 (26 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (26 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (32 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (34 페이지), 사용 설명서 지침 (34 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (34 페이지), 사용 설명서 지침 (26 페이지), 사용 설명서 (40 페이지), 사용 설명서 지침 (31 페이지), 사용 설명서 지침 (40 페이지), 사용 설명서 (24 페이지), 사용 설명서 (28 페이지), 사용 설명서 (28 페이지)

페이지 인쇄
Siemens dishwasher 사용 설명서
en
... when the appliance is
switched on
The appliance does not start.
– The mains fuse has tripped.
– The appliance plug has not been
inserted.
– The appliance door has not been shut
properly.
... changing settings
A setting cannot be changed, a
programme starts.
– Wrong programme button pressed.
Terminate the programme (see chapter
entitled "Terminating the programme
(Reset)") and start all over again.
– You did not wait until programme
ended.

... on the appliance

Lower spray arm rotates sluggishly.
– Spray arm blocked.
The door is difficult to open. *
– Child-proof lock is activated. The
deactivation instructions are at the
back in the envelope.
* depending on model
Door cannot be closed.
– Door lock has been activated. To reset,
close the door with greater force.
Cover on the detergent dispenser cannot
be closed.
– Detergent dispenser overfilled or
mechanism blocked by sticky
detergent residue.
Detergent residue in the detergent
dispenser.
– Dispenser was damp when filled.
"Check water supply" display @ lights
up.
– Tap turned off.
– Water supply interrupted.
– Supply hose kinked.
22
– Filter in the water supply blocked.
– Switch off the appliance and pull
out the mains plug.
– Turn off the tap.
– Clean filter in the supply hose.
– Reconnect power supply.
– Turn on the tap.
– Switch on the appliance.
– Water is left in the appliance
at the end of the programme.
– ( :
) Waste water hose
is blocked or kinked.
Filters blocked.
– ( :
) Waste water pump blocked,
cover on the waste water pump
is not locked in position
(see Waste water pump).
– Filters blocked.
– The programme has not yet ended.
Wait until programme ends (digital
display indicates :
implement the "Reset" function.
Error code :
– Filters 1j are soiled or blocked.
Refill indicator for salt H and/or rinse-
aid P is not lit.
– Refill indicator/s switched off.
– Adequate salt/rinse-aid available.
Refill indicator for special salt H is lit.
– No salt.
Refill with special salt.
– Sensor does not detect salt tablets.
Use different special salt.
) or