Digital Lighting Systems OPTIMA-DS Series 사용자 설명서 - 페이지 7

{카테고리_이름} Digital Lighting Systems OPTIMA-DS Series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Digital Lighting Systems OPTIMA-DS Series 10 페이지. Optima-ds series dmx chaser/cross-fader controllers

페이지 인쇄

Digital Lighting Systems

OPTIMA-DS2/DS2-C Operating Instructions

III.

Introduction

The OPTIMA-DS2 and DS2-C are

simplified versions of the OPTIMA-DS

controller. They have the same features

as the DS with the exception on the

master and individual dimming controls.

The DS2-C is the same as the Ds2 but is

locked on "chase only" by setting selector

S2 to 0. The FADE button on the DS2-C is

deactivated and does not perform any

IV.

Number of Channels

Configuration

The number of channels on both models

can be set to any value between 3 to 8

usaing rotary selector S1 on the back of

the unit. Refer to Fig. 8 to the right.

V. T

he Control Panel -

A -

Dual Button Controls

1- PATTERN (Up-Down Buttons)

The "PATTERN" up-button increments the pattern number from 1 to 16. The "PATTERN" down-button performs the reverse

operation until number 1 is reached.

2- SPEED (Up-Down Buttons)

The "SPEED" up-button increments the chase speed from 1 to 255. The "SPEED" down-button performs the reverse operation

until it reaches a minimum of 1.

The LED'S above these buttons indicate the output status of the first four channels.

B -

Single Button Toggle Controls

The following four buttons work as toggles. They turn the function on, if previously off, and turn it off, if previously on.

1 - FADE/CHASE SELECT

If the fade mode had been previously selected, depressing the Fade Select button

switches the OPTIMA-DS2 to the chase mode and vice-versa. The associated LED

turns on when the selected mode is fade. (Feature disabled on DS2-C version.)

2 - AUTO/MAN. SELECT

Selecting the AUTO/MAN. mode causes the OPTIMA-DS2 to automatically scroll

through all 16 chase patterns. Otherwise, the same pattern repeats unless changed

using the PATTERN up/down buttons. The associated LED is on when Auto is

selected.

3 - ALL ON SELECT

Selecting the ALL ON mode stops the chasing and fading cycles and causes all

channels to go into a static ALL ON mode. The associated LED is on when ALL ON

is selected.

4 - ALL OFF Select

All channels are blacked out and go to 0% intensity. When selected, the associated

LED turns on.

7588 NW 8th Street, Miami, Fl. 33126 Tel: 305-264-8391

OPTIMA-DS

Selector S2

Chase/Fade

OPTIMA-DS2 set to

"F"

(Chase and Fade)

OPTIMA-DS2-C set

to "0"

(Locked on Chase

Only)

Fig. 8 OPTIMA - number of Channels and Chase/Fade Selection

See figure 9 below.

Specifications are subject to change without notice.

DMX 3 - 8 Channel Controllers

Fig. 9 The OPTIMA-DS2 Front Panel

or 1-877-264-8391

Fax: 305-261-6637

Printed in U.S.A.

User's Manual - Page 6

Selector S1

Number of Channels

Using a small tip

screw driver, rotate

the shaft and

position the arrow at

the desired number.

Valid range: from 3

to 8 Channels.

OPTIMA-DS2

4 channel logic DMX512

Fade/

Chase

Pattern

Auto/

Man.

ALL

Speed

ALL

OFF

OSUM

Rev. A 09/01