Cisco 8841 매뉴얼 - 페이지 10

{카테고리_이름} Cisco 8841에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 8841 48 페이지. Mpp phones
Cisco 8841에 대해서도 마찬가지입니다: 릴리스 정보 (24 페이지), 사용자 설명서 (16 페이지), 빠른 참조 매뉴얼 (7 페이지), 특징 (16 페이지), 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (6 페이지), 사용자 설명서 (24 페이지), 사용자 설명서 (28 페이지), 펌웨어 마이그레이션 마스터 매뉴얼 (31 페이지), 사용자 설명서 (30 페이지), 사용자 설명서 (29 페이지), 매뉴얼 (44 페이지), 빠른 시작 매뉴얼 (2 페이지), 짧은 설명서 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 재구성 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (6 페이지), 매뉴얼 (22 페이지), 시작하기 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (40 페이지), 빠른 시작 (2 페이지)

페이지 인쇄
Cisco 8841 매뉴얼
Audio Quality
Before you begin
Access the phone administration web page. See
Procedure
Step 1
Select Voice > Provisioning.
Step 2
Under the Cisco Headset Firmware Upgrade section, find the parameter Cisco Headset Upgrade Rule.
Step 3
Specify the TFTP, HTTP, or HTTPS protocol, an IP address of the headset upgrade device, and the name of
the headset XML file. Enter the values as a single string in the parameter.
Caution
For example,
You can also configure this parameter in the configuration file (cfg.xml):
<Cisco_Headset_Upgrade_Rule
ua="na">tftp://10.74.51.81/prov/headset/1-6-0-162/ciscoheadsetfirmware.xml</Cisco_Headset_Upgrade_Rule>
Step 4
Click Submit All Changes.
If a new version of the headset firmware is detected, the phone displays an upgrade prompt.
Audio Quality
Beyond physical, mechanical, and technical performance, the audio portion of a headset must sound good to
the user and to the party on the far end. Sound quality is subjective, and we cannot guarantee the performance
of any third-party headset. However, various headsets from leading headset manufacturers are reported to
perform well with Cisco IP Phones.
Cisco doesn't recommend or test any third-party headsets with their products. For information about third-party
headset support for Cisco products, go to the manufacturer's web site.
Cisco does test the Cisco headsets with the Cisco IP Phones. For information about Cisco Headsets and Cisco
IP Phone support, see https://www.cisco.com/c/en/us/products/collaboration-endpoints/headsets/index.html.
Analog Headsets
The phone cannot detect when an analog headset is plugged in. For this reason, the analog headset displays
by default in the Accessories window on the phone screen.
Displaying the analog headset as the default allows users to enable wideband for the analog headset.
USB Headsets
Wired and wireless USB headsets are supported. You can connect one USB headset (or the base station for
a wireless headset) to either the back USB port (if your phone has this port) or to the side USB port.
Cisco IP Phone Accessories
10
Do not change the headset XML file contents.
tftp://10.74.51.81/prov/headset/1-6-0-162/ciscoheadsetfirmware.xml
Access the Phone Web
Interface.
Cisco IP Phone Accessories