Cisco 8861 사용자 설명서 - 페이지 6

{카테고리_이름} Cisco 8861에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 8861 29 페이지. Calltower vpn enabled phone
Cisco 8861에 대해서도 마찬가지입니다: 릴리스 정보 (24 페이지), 사용자 설명서 (16 페이지), 특징 (16 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (3 페이지), 사용자 설명서 (24 페이지), 사용자 설명서 (28 페이지), 펌웨어 마이그레이션 마스터 매뉴얼 (31 페이지), 사용자 설명서 (30 페이지), 매뉴얼 (44 페이지), 매뉴얼 (13 페이지), 매뉴얼 (14 페이지), 빠른 시작 매뉴얼 (2 페이지), 설치 매뉴얼 (39 페이지), 재구성 매뉴얼 (2 페이지), 빠른 사용 설명서 (2 페이지), 문제 해결 (4 페이지), 빠른 매뉴얼 (3 페이지), 매뉴얼 (22 페이지), 빠른 시작 매뉴얼 (2 페이지), 시작하기 (2 페이지), 매뉴얼 (48 페이지), 사용자 설명서 (40 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 (2 페이지)

Setting Up Your Phone

Before you begin installing your service, please make sure you have the following equipment:

A Cisco 8841/8851 and 8861 phone body.

•

A handset and cord.

A desk stand.

•

A CAT 5 Ethernet computer cable, to connect the phone to your router.

A power supply unit, including a plug lead and clip, assuming you're not using Power Over

•

Ethernet switches or ports.

A sheet with your phone number, online account user details and voicemail PIN - this is

•

important information, so please keep it somewhere safe, even after set-up.

•

A working Ethernet LAN with Ethernet broadband router - USB routers and modems are not

compatible.

A Power over Ethernet switch - or Ethernet switch - depending on your installation.

•

Now, start by putting the phone together in the following order:

•

First, find the coiled handset cord. Plug it into the smaller socket on the underside of the

phone - this is marked with a phone symbol.

Now, take the other end of the handset cord and plug it into the handset.

•

Line up the phone stand and the tabs with the slots on the underside of the phone. Slide the

bottom tabs into the slots and press lightly down on the top of the desk stand - don't force it.

Next, push the power brick into the plug unit and plug the power lead into the phone, to

•

assemble the power supply unit.

•

Connect the computer cable to the underside of the phone in the socket monitor/pc icon.

Before connecting the service, make sure your router is set up to perform NAT (Network Address

Translation) and act as a DHCP server - normally a default setting on most routers (a fixed IP

address is not supported).

Next, plug the Ethernet cable from the phone into your router. Once powered up, an IP address

should automatically be allocated to the phone through DHCP. It's also important to make sure the

following ports are not blocked by the firewall within your router or at any point through your access

provider.

Page

Horizon

Cisco IP Phone 8841/8851 and 8861 User Guide