Cisco Cisco 7940 참조 매뉴얼 - 페이지 13

{카테고리_이름} Cisco Cisco 7940에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Cisco 7940 17 페이지. 2 line appearance phone
Cisco Cisco 7940에 대해서도 마찬가지입니다: 사용자 설명서 (19 페이지), 사용자 설명서 (13 페이지), 사용자 설명서 (12 페이지), 맞춤형 사용자 설명서 (2 페이지), 매뉴얼 (35 페이지), 사용자 설명서 (15 페이지), 설치 및 구성 매뉴얼 (10 페이지), 사용자 설명서 (23 페이지), 사용자 설명서 (14 페이지), 참조 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 (13 페이지), 사용자 설명서 (16 페이지), 사용자 설명서 (9 페이지), 참조 매뉴얼 (4 페이지), 빠른 참조 매뉴얼 (8 페이지), 빠른 시작 매뉴얼 (12 페이지), 빠른 참조 매뉴얼 (12 페이지), 사용자 설명서 (20 페이지), 사용자 설명서 (14 페이지), 빠른 참조 매뉴얼 (12 페이지), 사용자 설명서 (6 페이지), 사용자 설명서 (3 페이지), 빠른 사용 설명서 (2 페이지), 빠른 설치 매뉴얼 (1 페이지), 매뉴얼 (21 페이지), 사용자 설명서 (3 페이지), 빠른 참조 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 참조 매뉴얼 (3 페이지), 사용자 설명서 (12 페이지), 사용자 설명서 (12 페이지), 사용자 설명서 (4 페이지), 빠른 사용 설명서 (2 페이지)

페이지 인쇄

STORING AND RETRIVEING PARKED CALLS

You can "park" a call when you want to store the call so that you or someone else can retrieve it from another phone in the Cisco

CallManager system (for example, a phone at a co-worker's desk or in a conference room). Call Park is a feature that your system

administrator must enable for you.

IF YOU WANT TO...

Store an active call using Call Park

Retrieve a parked call

TIPS

• To Park a call Dial

#700#

and a voice recording will give you an access key. Dial access key to retrieve the parked call.

REDIRECTING A RINGING CALL TO YOUR PHONE

Call PickUp allows you to redirect a call that is ringing on a co-worker's phone to your own phone so that you can answer the call. Call

PickUp is a special feature that your system administrator might enable for you, depending on your call-handling needs and work

environment. For example, you might use this feature if you share call-handling responsibilities with co-workers. You can handle calls

for co-workers who are in your "call pickup group," which is defined by your system administrator.

IF YOU WANT TO...

Answer a call that is ringing on another

extension within your group

Answer a call that is ringing on another

extension outside of your group

USING A HANDSET, HEADSET, AND SPEAKERPHONE

The table below describes how to use these devices.

IF YOU WANT TO...

Use the handset

Use a headset

Use the speakerphone

Switch to the speakerphone or headset

(from the handset) during a call

Switch to the handset (from the speak-

erphone or headset) during a call

SNET: CISCO 7940/7960 REFERENCE GUIDE

THEN...

During a call, press Park. (You may need to press the

number displayed on your phone screen and hang up.

Enter the call park number from any Cisco IP Phone in your network to connect to the call.

You have a limited amount of time to retrieve the parked call before it reverts to ringing at its original destination. See your system administra-

tor for this time limit.

THEN...

Press

(an available line button) and

Press

(an available line button) and *88+ext for party being called. The call now rings on your phone.

THEN...

Lift it to go off-hook; replace it to go on-hook.

Press

to toggle headset mode on and off.

You can use the headset in conjunction with all of the controls on your phone,

Press

to toggle speakerphone mode on or off.

Many of the actions you can take to dial a number or answer a call will automatically trigger speakerphone mode, assuming that the handset is

in its cradle and

is not lit.

Press

, then hang up the handset.

Lift the handset. There is no need to push any buttons.

softkey to see Park.) This prompts your phone to store the call. Note the call park

*8+ext

for party being called. The call now rings on your phone.

REFERENCE

including and

Back to Table of Contents