Cisco SPA302D 빠른 시작 매뉴얼

{카테고리_이름} Cisco SPA302D에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco SPA302D 2 페이지. Mobility enhanced cordless handset
Cisco SPA302D에 대해서도 마찬가지입니다: 사용자 설명서 (38 페이지), 데이터시트 (7 페이지), 사용자 설명서 (10 페이지), 소유자 매뉴얼 (49 페이지)

페이지 인쇄

Quick Start Guide

Cisco SPA302D Mobility Enhanced Cordless

Handset

Package Contents

• Cisco SPA302D Mobility Enhanced Cordless Handset

• Charging Cradle

• Belt Clip

• Power Adapter

• Power Clip

• Two rechargeable AAA batteries

Version en français sur CD

• Product CD-ROM

• Quick Start Guide

Welcome

Thank you for choosing the Cisco SPA302D. This guide describes how to

physically set up and register your Cisco SPA302D to the Cisco SPA232D ATA.

It also describes how to perform some basic tasks, such as placing and

answering calls, and configuring basic phone options.

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

• Cisco SPA232D Mobility Enhanced ATA, which has an integrated DECT

Base Station to provide telephone service for the SPA302D

• Active Internet connection

• Active Public Switched Telephone Network (PSTN) connection or Voice

over IP (VoIP) phone service account

• PC with web browser, for using web-based system management tools

(Microsoft Internet Explorer, Mozilla Firefox, and Apple Safari are supported)

Battery Warning

Use only size AAA Ni-MH 800 mAh (1.2V) rechargeable batteries in the

Cisco SPA302D handset. Place the handset in the charging cradle for a

recommended initial charge of 10 hours before using the handset for the first

time.

Cisco SPA302D Features

Table 1 Handset Features

Receiver.

Handset display.

Right softkey. Press the softkey to perform the action shown in the

lower right of the handset display.

End Call button. Press the button and hold it to turn off the handset.

Keypad.

Mute button.

Microphone.

Speakerphone button. Press this button during a call to use the

speakerphone.

Start Call button.

Left softkey. Press the softkey to perform the action shown in the lower

left of the handset display.

4-way navigation keypad. Press the arrow buttons to move up, down,

left, or right through menus displayed on the handset.

Center Select button.

Headset port.

Speaker.

Handset Setup and Registration

Charging the Handset

Remove the back cover of the handset.

TEP

Insert the two AAA rechargeable batteries (included) into the handset.

TEP

(See

Battery Warning

in "Before You Begin.")

Correct battery placement is shown on the label inside the battery

compartment. If the batteries are charged, the handset turns on when

the batteries are inserted. If the batteries are not charged, the handset

turns on when it is placed into the charging cradle.

Remove the protective film from the handset and charging cradle.

TEP

Insert the power clip into the power adapter.

TEP

Plug the power adapter into the power source.

TEP

Connect the power adapter into the charging cradle in the port shown

TEP

below.

Only use the power adapter designed for use with Cisco SPA300

AUTION

Series devices.

Place the handset into the charging cradle. The light on the charging

TEP

cradle appears solid green when the handset is charging. Charge the

handset for a minimum of 10 hours before using the handset for the

first time to ensure that the handset is fully charged.

Registering the Handset to the Cisco SPA232D Mobility

Enhanced ATA

Install and configure the Cisco SPA232D. See the Cisco SPA232D

TEP

Quick Start Guide for more information.

On the Cisco SPA302 handset, press the Select button in the center of

TEP

the 4-way navigation keypad.

Using the navigation arrows, scroll to the Settings icon and

TEP

press the center navigation button to select it.

Select Handset Registration.

TEP

Select Register.

TEP

On the Cisco SPA232D, press the Page/Registration button and hold

TEP

it down for at least seven seconds until the green status light flashes

quickly.

TIP: If you press the button for fewer than seven seconds, the green

status light flashes slowly, indicating the unit is in "paging" mode and is

not in registration mode. Registration will not work if the unit is in

paging mode.

The default PIN is blank, so do not enter a PIN. Press the left softkey to

TEP

confirm that you want to register the handset. The "registering"

message appears.

To verify that the handset registered to the base station,

TEP

confirm that the signal strength icon is solid (not flashing)

and that the handset ID, such as Handset 1 or Handset 2,

appears near the top right corner of the display screen.