Cisco Unified 7900 Series 사용자 설명서 - 페이지 5
{카테고리_이름} Cisco Unified 7900 Series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Unified 7900 Series 11 페이지. Release notes for firmware release 9.3(1)sr2
Cisco Unified 7900 Series에 대해서도 마찬가지입니다: 시스템 매뉴얼 (50 페이지), 솔루션 매뉴얼 (10 페이지), 시스템 매뉴얼 (36 페이지), 릴리스 정보 (20 페이지)
페이지 인쇄
Consult Transfer – redirects the call after first allowing
you to speak to the transfer recipient.
To transfer a call, use the following method:
During a call, press the Transfer soft key. The call is placed on
hold.
Dial the number to which you want to transfer the call.
To make a blind transfer:
Hang up the handset or press the Blind Xfr soft key after you
hear line ringing.
To make a consult transfer:
Wait for the call to be answered.
recipient. Then press the Trnsfer button or hand up the
handset.
To Cancel your consult call-transfer attempt:
Press the EndCall soft key.
To reconnect to the original caller:
Press the Resume soft key.
Note: To get the caller back, simply hit the Line button again.
5.2 FORWARD INCOMING CALLS
This feature allows calls to your primary extension to be redirected
to another extension number (i.e. another phone or to voicemail.
You can forward incoming calls to an IP phone or a non-IP phone.
To forward incoming calls:
Press the CfwdAll soft key.
Dial
extension number
to where you want your calls directed.
To cancel forward:
Press CfwdAll soft key.
To forward your calls to your voicemail:
Press CfwdAll soft key.
Press
Button
To cancel forward:
Press CfwdAll soft key.
5.3 HOLD A CALL
During an active call, press the Hold soft key.
To return to the call, press the Resume soft key.
If multiple calls are on hold, use the
desired call before you press Resume.
Cisco 7900 SeriesTelephone
Rollins College User Guide
Speak to the transfer
button to select the
Page 5 of 11
If multiple calls on multiple lines are on hold, press the line button
for the line that you want to pick up. The active call on the other
line is automatically put on hold.
5.4 CONFERENCE CALLS
This feature allows three people to simultaneously communicate via
the same line. While on an active call (either incoming or outgoing):
A standard conference call involves three parties.
To place a three-party conference call, use the following method:
During a call, press the more soft key and then the Confrn soft
key to open a new line and put the first party on hold.
Dial the number of the party to be added to the conference call.
When the call connects, press Confrn soft key again to add the
new party to the existing call with the first party.
Repeat the first three steps to add more callers.
End a Conference Call:
To end the conference call, use one of the following methods:
Hand up the handset.
Press the EndCall soft key.
Alternate Methods to End a Conference Call
Call initiators may use one of the following methods (functions vary
according to your system configuration):
To end the conference and remain connected to the most
recent call, press Confrn soft key. The older call is placed on
hold.
To disconnect from the conference, hang up the handset. The
other parties remain on the conference call.
Note:
Once the conference call initiator disconnects, no new
conferees can be added.
Keep in mind that when you place a call on hold a beeping tone
is generated every few seconds. To avoid disrupting the other
callers, consider muting the call instead.
To abandon the addition of a conferee, press the Line button
5.5 LAST NUMBER REDIAL
To redial the most recently dialed number, use one of the following
methods:
Lift the Handset and press the Redial soft key.
Press the Redial soft key to dial using the speakerphone.
Note: You can also press the Redial soft key to place the call via
Speakerphone.