Ricoh Aficio CL3000 빠른 설치 매뉴얼 - 페이지 2
{카테고리_이름} Ricoh Aficio CL3000에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ricoh Aficio CL3000 4 페이지. Sap printing
Ricoh Aficio CL3000에 대해서도 마찬가지입니다: 매뉴얼 (49 페이지), 설치 매뉴얼 (3 페이지), 보충 설명서 (3 페이지), 옵션 매뉴얼 (48 페이지), 보충 설명서 (38 페이지), 매뉴얼 (12 페이지)
페이지 인쇄
INSTALLING THE TONER
Check the toner color and location are correct,
and then insert the toner cartridge vertically and
CARTRIDGE
slowly.
You can check the location for each toner cartridge by reading the
Open the upper left cover of the printer.
labels on the printer.
ZHBH441E
Take out the toner cartridge.
In the illustration, yellow cartridge is used as an example.
Push the toner cartridge in the direction of the
arrow to fasten the toner cartridge.
Hold the toner cartridge horizontally as illustrated,
and then shake it back and forth about 10 times.
ZHBH460E
Repeat steps
In the illustration, black cartridge is used as an example.
toner cartridges.
Important
Do not open the shutter on the bottom of the toner
Close the upper left cover of the printer.
cartridge. Toner may spill.
ZHBH470E
Note
Remove the adhesive tapes.
If the toner cartridge is not set properly, you cannot
close the upper left cover of this printer.
ZHBH910E
LOADING PAPER
Caution
When pulling the paper tray out, be careful not
to pull it strongly. If you do, the tray might fall
and cause personal injury.
Pull the paper tray out of the printer until it stops.
After that, lift it slightly, and then pull it out
completely. Place it on a flat surface.
ZHBH481E
Note
You cannot pull the Tray 1 out if the Bypass Tray is
open.
Remove the adhesive tape and packing material.
ZHBH491E
to , to install the other color
Press "Push", and then adjust the rear guide to
the paper size you want to load.
ZHBH500E
Adjust the side guides to the paper size you want
to load.
Load paper into the paper tray with the print side
up.
Important
Make sure that the top of the stack is not higher
than the limit mark inside the tray.
The front and side guides should be set exactly to
the paper size to avoid paper misfeeds.
Do not load different kinds of paper in the tray.
Slide the paper tray completely into the printer.
CONNECTING THE POWER
ZHBY010E
CORD
Warning
It is dangerous to handle the plug with wet hands.
Doing this may result in receiving an electric
shock.
Caution
When you pull the plug out of the socket, grip
the plug, not the cord, to avoid damaging the
cord and causing a fire or an electric shock.
Important
Be sure to connect the power plug to the socket or
the wall outlet firmly.
The printer power must be off when plugging in and
ZHBY920E
out the power cord.
Confirm that the printer's power switch is off. If it
is on, turn it off.
ZHBY040E
ZHBH730E
Attach the power cord to the socket on the back
of the printer.
ZHBY060E
ZHBH030E
Plug the other end securely into the wall outlet.
SELECTING THE PANEL
Press the { } or { } key to display
"Language".
DISPLAY LANGUAGE
Menu:
Follow the procedure to select a language.
Language
Note
Press the {Enter #} key.
You can select one of the following languages:
English, German, French, Italian, Dutch, Swedish,
The following message appears on the panel display.
Norwegian, Danish, Spanish, Finnish, Portuguese,
Czech, Polish or Hungarian.
Language:
The default setting is English.
*English
If you want to use the English panel display, it is
not necessary for you to take the following
Press the { } or { } key to display
procedures.
the language you want to select.
Turn on the printer.
Press the {Enter #} key.
"Menu" appears on the panel display.
Menu:
Language
Press the {On Line} key.
"Ready" appears on the panel display.
Ready
ZHBH740E
After the machine warms up, "Ready" appears on the panel display.
Ready
Press the {Menu} key.
ZHBS010E
The following message appears on the panel display.
Menu:
Paper Input
Go to sheet 2/2.
Sheet 1/2