Cisco 3745 사용자 설명서 - 페이지 31
{카테고리_이름} Cisco 3745에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 3745 48 페이지. Non-proprietary security policy
Cisco 3745에 대해서도 마찬가지입니다: 솔루션 개요 (16 페이지), 업그레이드 지침 (30 페이지), 빠른 시작 매뉴얼 (33 페이지), 설치 매뉴얼 (12 페이지)
페이지 인쇄
Place the fourth label on the router as shown in
Step 5
so that the half of the label covers the enclosure and the other half covers the WAN interface card slot.
Any attempt to remove a WAN interface card will leave tamper evidence.
Step 6
Place the fifth label on the router as shown in
that one half of the label covers the enclosure and the other half covers the WAN interface card slot. Any
attempt to remove a WAN interface card will leave tamper evidence.
Step 7
The labels completely cure within five minutes.
Figure 21
RPS ACTIVITY
To apply serialized tamper-evidence labels to the Cisco 2691:
Clean the cover of any grease, dirt, or oil before applying the tamper evidence labels. Alcohol-based
Step 1
cleaning pads are recommended for this purpose. The temperature of the router should be above 10°C.
Place the first label on the router as shown in
Step 2
that the one half of the tamper evidence label covers the enclosure and the other half covers the right side
of the router. Any attempt to remove the enclosure will leave tamper evidence.
Step 3
Place the second label on the router as shown in
so that the one half of the tamper evidence label covers the enclosure and the other half covers the left
side of the router. Any attempt to remove the enclosure will leave tamper evidence.
Place the third label on the router as shown in
Step 4
that the one half of the label covers the enclosure and the other half covers the Network Module slot.
Any attempt to remove a Network Module will leave tamper evidence.
Place the fourth label on the router as shown in
Step 5
so that the half of the label covers the enclosure and the other half covers the left WAN interface card
slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Place the fifth label on the router as shown in
Step 6
that one half of the label covers the enclosure and the other half covers the middle WAN interface card
slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Place the sixth label on the router as shown in
Step 7
that one half of the label covers the enclosure and the other half covers the right WAN interface card slot.
Any attempt to remove a WAN interface card will leave tamper evidence.
Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, and 3745 Modular Access Routers and 7206-VXR NPE-400 Router FIPS 140-2 Non-Proprietary
OL-6083-01
The Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, 3745, and 7206 VXR NPE-400 Routers
Cisco 2621XM and Cisco 2651XM Tamper Evidence Label Placement
W1
LINK
ETHERNET 1
ACT
LINK
ETHERNET 0 ACT
CONSOLE
AUX
Figure
21. The tamper evidence label should be placed
Figure
21. The tamper evidence label should be placed so
Cisco 2611
100-240V– 1A
50/60 Hz 47 W
W0
Cisco 2600
SERIES
Figure
22. The tamper evidence label should be placed so
Figure
22. The tamper evidence label should be placed
Figure
22. The tamper evidence label should be placed so
Figure
22. The tamper evidence label should be placed
Figure
22. The tamper evidence label should be placed so
Figure
22. The tamper evidence label should be placed so
31