Cisco RV120W 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Cisco RV120W에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco RV120W 2 페이지. Factory reset and reboot
Cisco RV120W에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (21 페이지), 매뉴얼 (2 페이지)

페이지 인쇄

Connect the power adapter to the Cisco RV120W power port.

TEP

Use only the power adapter that is supplied with the unit. Using

AUTION

a different power adapter could damage the unit.

Plug the other end of the adapter into an electrical outlet.

TEP

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

www.cisco.com

Small Business Support, Global: www.cisco.com/go/sbsc

78-19197-02

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and

other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.

Third party trademarks mentioned are the property of their respective owners. The use of the word

partner does not imply a partnership relationship between Cisco and any other company. (1005R)

On the Cisco RV120W, push in the ON/OFF POWER SWITCH button.

TEP

The POWER LED on the front panel lights up green when the power

adapter is connected properly and the unit is turned on.

Cisco RV120W Features

Front Panel

Power—The Power LED lights up green to indicate the unit is powered on. It

flashes green when the power is coming on or software is being upgraded.

WAN LED—The WAN (Internet) LED lights up green when the unit is connected

to your cable or DSL modem. The LED flashes green when the unit is sending

or receiving data over the WAN port.

Wireless—The Wireless LED lights up green when the wireless module is

enabled. The LED is off when the wireless module is disabled. The LED flashes

green when the unit is transmitting or receiving data on the wireless module.

LAN—These four LEDs correspond to the four LAN (Ethernet) ports of the

Cisco RV120W. If the LED is continuously lit green, the Cisco RV120W is

connected to a device through the corresponding port (1, 2, 3, or 4). The LED

for a port flashes green when the Cisco RV120W is actively sending or

receiving data over that port.

Back Panel

RESET Button—The Reset button has two functions:

• If the Cisco RV120W is having problems connecting to the Internet, press

the RESET button for less than five seconds with a paper clip or a pencil tip.

This is similar to pressing the reset button on your PC to reboot it.

• If you are experiencing extreme problems with the Cisco RV120W and have

tried all other troubleshooting measures, press and hold in the RESET

button for 10 seconds. This restores the factory defaults and clear all of the

Cisco RV120W settings.

LAN Ports (1-4)—These ports provide a LAN connection to network devices,

such as PCs, print servers, or additional switches.

WAN Port—The WAN port is connected to your Internet device, such as a

cable or DSL modem.

ON/OFF POWER SWITCH—Press this button to turn the Cisco RV120W on

and off. When the button is pushed in, power is on.

Power Port—The power port is where you connect the AC power cable.

Default Settings

Parameter

Default Value

Username

admin

Password

admin

LAN IP

192. 1 68. 1 . 1

DHCP Range

192. 1 68. 1 . 1 00 to

192. 1 68. 1 .254

Netmask

255.255.255.0

Getting Started with the Device Manager

Before you begin to use the Device Manager, make sure that you have a

computer and browser as described in the

Before You Begin

section. The

Device Manager provides a Setup Wizard to perform basic configuration for

the firewall. You can also perform advanced configuration tasks in the Device

Manager, and access online help for your Cisco RV120W.

Connect your computer to the Cisco RV120W as described in the

TEP

Connecting the Equipment

section. Your PC will become a DHCP

client of the firewall and will receive an IP address in the 192. 1 68. 1 .XXX

range.

Start a web browser on your PC. In the Address Bar, enter the default

TEP

IP address of the firewall: 192. 1 68. 1 . 1 . A message appears about the

site's security certificate. The Cisco RV120W uses a self-signed

security certificate and this message appears because the firewall is

not known to your PC. You can safely click Continue to this website (or

the option shown on your particular web browser) to go to the web

site.

When you connect to the firewall, the Setup Wizard appears. Follow

TEP

the on-screen prompts in the Setup Wizard to configure your firewall.

Where to Go From Here

Support

Cisco Small Business

www.cisco.com/go/smallbizsupport

Support Community

Cisco Small Business

www.cisco.com/go/smallbizhelp

Support and Resources

Phone Support Contacts

www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Small Business

www.cisco.com/cisco/web/download/

Firmware Downloads

index.html

Select a link to download firmware for Cisco

Small Business Products. No login is

required.

Cisco Small Business

www.cisco.com/go/

Open Source Requests

smallbiz_opensource_request

Product Documentation

Cisco Small Business RV

www.cisco.com/go/smallbizrouters

Series Routers/Firewalls

Cisco Small Business

Cisco Partner Central

www.cisco.com/web/partners/sell/smb

for Small Business

(Partner Login Required)

Cisco Small Business

www.cisco.com/smb

Home