CABASSE ARCHIPEL 13ICD 소유자 매뉴얼 - 페이지 5

{카테고리_이름} CABASSE ARCHIPEL 13ICD에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CABASSE ARCHIPEL 13ICD 6 페이지. Loudspeakers

페이지 인쇄

e n g l i s h

UNPACKING

After opening the top carton flaps, fold the carton flaps right

back and invert the carton contents. Remove the cutting tem-

plate and the upper foam form, then the grills followed by the

speakers. Keep the grilles away from the work area until you

are ready to fit them. We suggest you to retain the packing for

future use.

Check the contents :

2 speakers with 1 round and 1 square grille each

1 alignment template

SET-UP AND POSITIONING

Check that there is no conflict with other installations

(pipe work, air conditioning, powercabling etc.). In existing

construction, use a stud-finding tool to map the construction

accurately and a pipe detector to scan the proposed installa-

tion position. Avoid installing the speakers in the same cavity

as flimsy ducting, which may be induced to rattle. The spea-

kers are designed to operate satisfactorily in a wide range of

cavity volumes, ideally above 13 litres (0.46 cu ft). Placement

near a wall/ceiling junction or in a corner is to be avoided as

it may give rise to too much bass and a boomy quality to the

sound. If possible, keep the speakers more than 0.5 m (20 in)

from the ceiling edges.

Damping the wall cavity

In addition, loosely fill the whole section of the cavity with

wadding. Fibreglass and mineral wool matting supplied for

heat insulation are suitable, but not closed cell foam or ex-

panded polystyrene. Check that there is no debris that may

fall into the speaker (especially in ceiling mount situations).

IMPORTANT: YOU SHOULD CHECK THAT THE MATE-

RIALS YOU USE MEET THE LOCAL FIRE AND BUILDING

REGULATIONS.

To get the best possible results, we advise you to use the ap-

propriate optional item, either the Cabasse backbox

Archipel 13, or the kit for drywall mounting

Set-up

Position the template on the surface as required. Mark

around the outside of the template

neatly

Connect the speaker cable to the terminals

amplifier. Respect the phase.

Position the frame in the wall or ceiling and screw in the

4 screws visible from the front of the frame

swing out clamping dogs that locate behind the drywall.

Ensure that they have located properly and tighten the

screws. A certain amount of flexing of the frame is allowed

to take up unevenness in the mounting surface, but do not

over tighten the screws as excessive distortion of the frame

may occur.

If necessary, swivels the tweeter towards the listening area

with a gentle pressure on it's perimeter. Do no touch the

dome diaphragm of the tweeter.

The rotation is possible in every direction within an

up to 20° for the 13ICP and 30° for the 13ICD.

automatically be fitted thanks to the magnetic link. It is pos-

sible to rotate the grille once fitted.

Customising

The grille has a paintable white semi-matte finish, ready if ne-

cessary to be re-finished to match your own decor.

ATTENTION: TURN OFF ALL THE AMPLIFIERS BEFORE

INTERCONNECTING THEM TO THE LOUDSPEAKERS. IN

ORDER TO CONNECT LOUDSPEAKERS PROPERLY, IT IS

MOST IMPORTANT TO KEEP IN MIND THE FOLLOWING

TWO FACTORS: CABLE SECTION AND PHASE.

CONNECTION

Cable section

To get the full sonic potential of Cabasse loudspeakers and

avoid power losses, the cables connecting the speakers to the

power amplifier must have the lowest possible electrical resis-

tance. To help you in choosing the correct cable gauge, follow

diagram.

Phase

Amplifier and speaker manufacturers typically indicate

connection polarity in one of two ways: red and black or

plus and minus. In either

for

case, always connect red

or plus to red or plus

and black or minus to

black or minus. Connec-

tions should be identical

and cut the aperture

for all channels.

and to the

AFTER SALE SERVICE

Cabasse retailers' network is at your disposal to ensure the

. These screws

after sale service of your material. To get the list of Cabasse

retailers, contact us or consult our web site www.cabasse.com.

Thanks to the above information, your installation is now

nicely set up and we hope you will enjoy your speaker system

for many years. We receive every day letters from customers

expressing the ever growing satisfaction and musical emotion

they have been getting with our speakers over the years. These

letters are our first motivation.

Position the grille of your choice in front of the speaker. It will

amplifier and loudspeakers

angle

Length between

Recommended

section

4,5 m

1,5 mm

6 m

2 mm

7,5 m

2,5 mm

9 m

3 mm

12 m

4 mm