Cisco 8865 설치 매뉴얼 - 페이지 38

{카테고리_이름} Cisco 8865에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 8865 39 페이지. Multiplatform phones
Cisco 8865에 대해서도 마찬가지입니다: 특징 (16 페이지), 사용자 설명서 (24 페이지), 사용자 설명서 (28 페이지), 펌웨어 마이그레이션 마스터 매뉴얼 (31 페이지), 사용자 설명서 (30 페이지), 사용자 설명서 (23 페이지), 매뉴얼 (44 페이지), 매뉴얼 (43 페이지), 매뉴얼 (14 페이지), 재구성 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (13 페이지), 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (8 페이지), 매뉴얼 (48 페이지), 매뉴얼 (11 페이지), 사용자 설명서 (40 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

Technical Details

Table 5: Guidelines for Cisco IP Conference Phone 8832 Power

Power Type

PoE power—Provided by either the Cisco

IP Conference Phone 8832 PoE Injector or

Cisco IP

Conference Phone 8832 Ethernet injector

through the USB-C cable attached to the

phone.

External power

• Non-PoE Ethernet deployment

with a Cisco IP Conference Phone

8832 Non-PoE Ethernet Injector

• Wi-Fi deployment with a Cisco

IP Conference Phone 8832 Power

Adapter

• Non-PoE Ethernet deployment

with a Cisco IP Conference Phone

8832 Ethernet Injector and a Cisco

IP Conference Phone 8832 Power

Adapter

See the following documents for more information about the products or solutions with Cisco IP Phones:

• Cisco switches that work with Cisco IP Phones

https://www.cisco.com/c/en/us/products/switches/index.html

• Cisco IOS releases that support bidirectional power negotiation

https://www.cisco.com/c/en/us/solutions/enterprise-networks/upoe/index.html

• Other requirements and restrictions about power

http://www.cisco.com/c/en/us/solutions/enterprise-networks/power-over-ethernet-solutions/index.html

https://www.cisco.com/c/en/us/products/routers/index.html

Installation Guide for Cisco IP Phone with Multiplatform Firmware

Guidelines

If you are using either the Cisco IP Conference Phone 8832 PoE

Injector or Cisco IP Conference Phone 8832 Ethernet Injector,

make sure that the switch has a backup power supply to ensure

uninterruptible operation of the phone.

Ensure that the CatOS or IOS version that runs on your switch

supports your intended phone deployment. See the documentation

for your switch for operating system version information.

When you install a phone that is powered by PoE, connect the

injector to the LAN before you connect the USB-C cable to the

phone. When you remove a phone that uses PoE, disconnect the

USB-C cable from the phone before you remove the power from

the adapter.

When you install a phone that is powered with external power,

connect the injector to power and to the Ethernet before you

connect the USB-C cable to the phone. When you remove a phone

that uses external power, disconnect the USB-C cable from the

phone before you remove the power from the adapter.

Phone Power Requirements